Go to the documentation of this file.
42 #ifdef PREINIT_SUPPORTED
46 #ifdef MikroCCoreVersion
47 #if MikroCCoreVersion >= 1
52 #include "drv_digital_out.h"
53 #include "drv_digital_in.h"
54 #include "drv_i2c_master.h"
67 #define TEMPHUM6_MAP_MIKROBUS( cfg, mikrobus ) \
68 cfg.scl= MIKROBUS( mikrobus, MIKROBUS_SCL ); \
69 cfg.sda= MIKROBUS( mikrobus, MIKROBUS_SDA )
76 #define TEMPHUM6_RETVAL uint8_t
78 #define TEMPHUM6_OK 0x00
79 #define TEMPHUM6_INIT_ERROR 0xFF
86 #define TEMPHUM6_PART_ID 0x0210
87 #define TEMPHUM6_DEVICE_SLAVE_ADDRESS 0x43
94 #define TEMPHUM6_REG_PART_ID 0x00
95 #define TEMPHUM6_REG_UNIQUE_IDENTIFIER 0x04
96 #define TEMPHUM6_REG_SYSTEM_CONTROL 0x10
97 #define TEMPHUM6_REG_SYSTEM_STATUS 0x11
98 #define TEMPHUM6_REG_SENS_RUN 0x21
99 #define TEMPHUM6_REG_SENS_START 0x22
100 #define TEMPHUM6_REG_SENS_STOP 0x23
101 #define TEMPHUM6_REG_SENS_STATUS 0x24
102 #define TEMPHUM6_REG_TEMPERATURE 0x30
103 #define TEMPHUM6_REG_RELATIVE_HUMIDITY 0x33
110 #define TEMPHUM6_STATUS_I2C_ERROR 4
111 #define TEMPHUM6_STATUS_CRC_ERROR 3
112 #define TEMPHUM6_STATUS_INVALID 2
113 #define TEMPHUM6_STATUS_OK 1
120 #define TEMPHUM6_TEMP_IN_FAHRENHEIT 2
121 #define TEMPHUM6_TEMP_IN_KELVIN 1
122 #define TEMPHUM6_TEMP_IN_CELSIUS 0
129 #define TEMPHUM6_LOW_POWER_DISABLE 0x00
130 #define TEMPHUM6_LOW_POWER_ENABLE 0x01
137 #define TEMPHUM6_SYSTEM_IS_IN_STANDBY_OR_BOOTING_STATE 0
138 #define TEMPHUM6_SYSTEM_IS_IN_ACTIVE_STATE 1
145 #define TEMPHUM6_HUM_RUN_SINGLE_SHOT_MODE 0x00
146 #define TEMPHUM6_TEMP_RUN_SINGLE_SHOT_MODE 0x00
147 #define TEMPHUM6_HUM_RUN_CONTINUOUS_MODE 0x02
148 #define TEMPHUM6_TEMP_RUN_CONTINUOUS_MODE 0x01
155 #define TEMPHUM6_HUM_START_MEASUREMENT 0x02
156 #define TEMPHUM6_TEMP_START_MEASUREMENT 0x01
157 #define TEMPHUM6_DISABLE_MEASUREMENT 0x00
164 #define TEMPHUM6_HUM_STOP_CONTINUOUS_MEASUREMENT 0x02
165 #define TEMPHUM6_TEMP_STOP_CONTINUOUS_MEASUREMENT 0x01
166 #define TEMPHUM6_DISABLE_CONTINUOUS_MEASUREMENT 0x00
325 #endif // _TEMPHUM6_H_
uint8_t slave_address
Definition: temphum6.h:189
uint16_t temphum6_get_part_id(temphum6_t *ctx)
Functions for get device PART ID.
i2c_master_t i2c
Definition: temphum6.h:185
TEMPHUM6_RETVAL temphum6_init(temphum6_t *ctx, temphum6_cfg_t *cfg)
Initialization function.
void temphum6_generic_write(temphum6_t *ctx, uint8_t reg, uint8_t *data_buf, uint8_t len)
Generic write function.
void temphum6_run(temphum6_t *ctx)
Functions for RUN measurement.
#define TEMPHUM6_RETVAL
Definition: temphum6.h:76
float temphum6_read_temperature(temphum6_t *ctx, uint8_t temp_in)
Functions for read Temperature data.
Click ctx object definition.
Definition: temphum6.h:182
void temphum6_generic_read(temphum6_t *ctx, uint8_t reg, uint8_t *data_buf, uint8_t len)
Generic read function.
float temphum6_read_relative_huminidy(temphum6_t *ctx)
Functions for read Relative Huminidy data.
Click configuration structure definition.
Definition: temphum6.h:197
pin_name_t scl
Definition: temphum6.h:200
uint8_t i2c_address
Definition: temphum6.h:206
uint32_t i2c_speed
Definition: temphum6.h:205
void temphum6_cfg_setup(temphum6_cfg_t *cfg)
Config Object Initialization function.
pin_name_t sda
Definition: temphum6.h:201
void temphum6_reset(temphum6_t *ctx)
Functions for reset device.