Go to the documentation of this file.
38 #include "drv_digital_out.h"
39 #include "drv_digital_in.h"
40 #include "drv_i2c_master.h"
52 #define TEMPHUM13_MAP_MIKROBUS( cfg, mikrobus ) \
53 cfg.scl = MIKROBUS( mikrobus, MIKROBUS_SCL ); \
54 cfg.sda = MIKROBUS( mikrobus, MIKROBUS_SDA )
61 #define TEMPHUM13_RETVAL uint8_t
63 #define TEMPHUM13_OK 0x00
64 #define TEMPHUM13_INIT_ERROR 0xFF
71 #define TEMPHUM13_DEVICE_ADDRESS 0x40
78 #define TEMPHUM13_CMD_TRIG_TEMP_MEAS_HOLD 0xE3
79 #define TEMPHUM13_CMD_TRIG_HUMI_MEAS_HOLD 0xE5
80 #define TEMPHUM13_CMD_TRIG_TEMP_MEAS_NOHOLD 0xF3
81 #define TEMPHUM13_CMD_TRIG_HUMI_MEAS_NOHOLD 0xF5
82 #define TEMPHUM13_CMD_WRITE_USER_REG 0xE6
83 #define TEMPHUM13_CMD_READ_USER_REG 0xE7
84 #define TEMPHUM13_CMD_SOFT_RESET 0xFE
92 #define TEMPHUM13_HEATER_ENABLE 0x01
93 #define TEMPHUM13_HEATER_DISABLE 0x00
100 #define TEMPHUM13_RESOLUTION_8 0x01
101 #define TEMPHUM13_RESOLUTION_10 0x80
102 #define TEMPHUM13_RESOLUTION_11 0x81
103 #define TEMPHUM13_RESOLUTION_12 0x00
110 #define TEMPHUM13_OTP_DISABLE 0x01
111 #define TEMPHUM13_OTP_ENABLE 0x00
328 #endif // _TEMPHUM13_H_
void temphum13_generic_read(temphum13_t *ctx, uint8_t reg, uint8_t *data_buf, uint8_t len)
Generic read function.
uint8_t slave_address
Definition: temphum13.h:133
void temphum13_soft_reset(temphum13_t *ctx)
Software reset.
Click configuration structure definition.
Definition: temphum13.h:141
void temphum13_generic_write(temphum13_t *ctx, uint8_t reg, uint8_t *data_buf, uint8_t len)
Generic write function.
#define TEMPHUM13_RETVAL
Definition: temphum13.h:61
pin_name_t scl
Definition: temphum13.h:144
pin_name_t sda
Definition: temphum13.h:145
uint32_t i2c_speed
Definition: temphum13.h:149
uint8_t temphum13_enable_heater(temphum13_t *ctx, uint8_t enable_heater)
Enable heater.
uint8_t i2c_address
Definition: temphum13.h:150
float temphum13_get_humidity(temphum13_t *ctx)
Get humidity value.
float temphum13_get_temperature(temphum13_t *ctx)
Get temperature value.
uint8_t temphum13_disable_otp_reload(temphum13_t *ctx, uint8_t disable_otp_rel)
Disable OTP.
void temphum13_cfg_setup(temphum13_cfg_t *cfg)
Config Object Initialization function.
Click ctx object definition.
Definition: temphum13.h:126
TEMPHUM13_RETVAL temphum13_init(temphum13_t *ctx, temphum13_cfg_t *cfg)
Initialization function.
uint8_t temphum13_get_user_register(temphum13_t *ctx)
Get user register value.
i2c_master_t i2c
Definition: temphum13.h:129
void temphum13_default_cfg(temphum13_t *ctx)
Click Default Configuration function.
void temphum13_set_user_register(temphum13_t *ctx, uint8_t register_content)
Set user register.
uint8_t temphum13_change_resolution(temphum13_t *ctx, uint8_t meas_res)
Change measurement resolution.