leddriver19 2.1.0.0
Main Page

LED Driver 19 click

PRVIH_PAR_RECENICA_SA_PRODUCT_PAGE_DA_ISPRATE_CELINU

[click Product page](CLICK_PRODUCT_PAGE_LINK)


Click library

  • Author : Stefan Ilic
  • Date : Apr 2023.
  • Type : I2C type

Software Support

We provide a library for the LED Driver 19 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for LED Driver 19 Click driver.

Standard key functions :

Example key functions :

Example Description

This library contains API for LED Driver 19 Click driver.

The library initializes and defines the I2C bus drivers to write the default configuration for a PWM output value of the out pins.

The demo application is composed of two sections :

Application Init

Initializes the driver and performs default configuration, sets the device

in output enabled mode and checks communication by reading device ID.

void application_init ( void )
{
log_cfg_t log_cfg;
leddriver19_cfg_t leddriver19_cfg;
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
leddriver19_cfg_setup( &leddriver19_cfg );
LEDDRIVER19_MAP_MIKROBUS( leddriver19_cfg, MIKROBUS_1 );
if ( I2C_MASTER_ERROR == leddriver19_init( &leddriver19, &leddriver19_cfg ) )
{
log_error( &logger, " Communication init." );
for ( ; ; );
}
uint8_t device_id;
leddriver19_read_reg( &leddriver19, LEDDRIVER19_REG_DEVICE_ID, &device_id );
if ( LEDDRIVER19_DEVICE_ID != device_id )
{
log_error( &logger, " Communication error." );
for ( ; ; );
}
if ( LEDDRIVER19_ERROR == leddriver19_default_cfg ( &leddriver19 ) )
{
log_error( &logger, " Default configuration." );
for ( ; ; );
}
log_info( &logger, " Application Task " );
}
#define LEDDRIVER19_MAP_MIKROBUS(cfg, mikrobus)
MikroBUS pin mapping.
Definition: leddriver19.h:279
#define LEDDRIVER19_REG_DEVICE_ID
LED Driver 19 description register.
Definition: leddriver19.h:59
#define LEDDRIVER19_DEVICE_ID
LED Driver 19 description setting.
Definition: leddriver19.h:109
err_t leddriver19_read_reg(leddriver19_t *ctx, uint8_t reg, uint8_t *data_out)
LED Driver 19 I2C register reading function.
@ LEDDRIVER19_ERROR
Definition: leddriver19.h:327
void application_init(void)
Definition: main.c:33

Application Task

This example demonstrates the use of the LED Driver 19 Click board by

changing PWM values of all channels from maximum to minimum turning LEDs on and off in the process.

void application_task ( void )
{
for ( uint8_t n_cnt = LEDDRIVER19_CH_SEL_0; n_cnt <= LEDDRIVER19_CH_SEL_11; n_cnt++ )
{
leddriver19_set_pattern_pwm( &leddriver19, LEDDRIVER19_PATSEL_0, n_cnt, 100 );
Delay_ms( 100 );
}
Delay_ms( 1000 );
for ( uint8_t n_cnt = LEDDRIVER19_CH_SEL_0; n_cnt <= LEDDRIVER19_CH_SEL_11; n_cnt++ )
{
Delay_ms( 100 );
}
Delay_ms( 1000 );
}
#define LEDDRIVER19_CH_SEL_11
Definition: leddriver19.h:157
#define LEDDRIVER19_CH_SEL_0
LED Driver 19 channel enable setting.
Definition: leddriver19.h:146
#define LEDDRIVER19_PATSEL_0
LED Driver 19 pattern state setting.
Definition: leddriver19.h:132
void application_task(void)
Definition: main.c:78

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.LEDDriver19

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.