Code Categories

All codes (4839)

TOP Contributors

  1. MIKROE (2656 codes)
  2. Alcides Ramos (353 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (112 codes)
  5. Chisanga Mumba (90 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (136870 times)
  2. FAT32 Library (70000 times)
  3. Network Ethernet Library (55999 times)
  4. USB Device Library (46301 times)
  5. Network WiFi Library (41907 times)
  6. FT800 Library (41206 times)
  7. GSM click (29012 times)
  8. PID Library (26423 times)
  9. mikroSDK (26394 times)
  10. microSD click (25385 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Example

GSM Click - Init Module, send text Message and easy Modem reply check

Rating:

0

Author: Alexander Wolf

Last Updated: 2014-08-21

Package Version: 1.0.0.0

Example: 1.0.0.0

Category: GSM / GPRS

Downloaded: 2480 times

Followed by: 5 users

License: MIT license  

Sending a Hello World text message. After init Modem and sent a message the modem can be controlled and tested via any Terminal programm using UART interrupts. A simple code using strstr to wait for and check Modem responses.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "GSM Click - Init Module, send text Message and easy Modem reply check " changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "GSM Click - Init Module, send text Message and easy Modem reply check " changes.

Do you want to report abuse regarding "GSM Click - Init Module, send text Message and easy Modem reply check ".

  • Information
  • Comments (2)
Download

Download All [3.52KB]

DOWNLOAD LINK RELATED COMPILER CONTAINS
1382006016_gsm_click___init_mikroc_pic32.zip [3.22KB] mikroC PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc

Example Blog

Blog currently doesn't exist!

ALSO FROM THIS AUTHOR

PIC32 MX SD Card Bootloader

9

This is a SD Card Bootloader for PIC32 MX. The hard work making this work did M. Hooper. I added FAT32 and some little things to make it work on Fusion V7 board. Attached is a PDF manual which describes more: 1. flash bootloader to your MCU 2. add some lines to your Application 3. rename and save hex file on sd card 4. start and push button RB0

[Learn More]

EEPROM 3 click AT24CM02 and other 16 Bit Adress EEPROM and FRAM

0

simple example for Read/write Byte for AT24CM02 EEPROM. Even the example is in C and for PIC32, it should be easy to adopt to other languages, since its a complete project. If AdressBits are changed, it also works with other 16 Bit adress I2C EEPROM &amp; FRAM

[Learn More]

BNO055 BOSCH 9DOF Config and Read Example

0

I use the BNO055 for Drones and Balancing Robots. Its a Basic example in configuring and readig the chip. In combination with the Datasheet it should be adoptable to other languages than C for PIC32. If the crappy MikroE Exampe doesnt work, check this out. Check for correct PIN connections because I dont use mikroBus

[Learn More]

codegrip for stm32