We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: GPS/GNSS
Downloaded: 75 times
Not followed.
License: MIT license
Download [468.56KB]GNSS 14 Click is a compact add-on board that provides fast positioning capability to your application. This board features the MIA-M10Q, a standard precision GNSS module from u-blox. It has an exceptional sensitivity and acquisition time for all L1 GNSS signals, attributed to its integrated M10 standard precision low-power platform. The M10 platform supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes position availability, particularly under challenging conditions like deep urban canyons.
[learn more]Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.4
mikroSDK Library: 2.0.0.0
Category: Port expander
Downloaded: 47 times
Not followed.
License: MIT license
Download [485.91KB]Expand 3 Click is a compact add-on board providing general-purpose I/O expansion. This board features the DS2408, an 8-channel programmable I/O expander from Analog Devices. The DS2408 has a factory-lasered 64-bit registration number, enabling multiple Expand 3 Click boards™ to be connected on the same data line, communicating with the host MCU through a standard Dallas Semiconductor 1-Wire interface (15.3kbps or 100kbps). PIO outputs are configured as open-drain and provide a maximum on-resistance of 100Ω.
[learn more]Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: RFID/NFC
Downloaded: 91 times
Not followed.
License: MIT license
Download [567.95KB]NFC 6 Click is a compact add-on board that contains an NFC transceiver for contactless communication. This board features the ST25R95, a near-field communication transceiver from STMicroelectronics. It supports reader and writer operating modes and emulates ISO/IEC 14443-3 Type A cards. The RF communications are done over the 13.56MHz. The transceiver features tag detection mode, field detection mode, transmission and reception modes, and more.
[learn more]Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 59 times
Not followed.
License: MIT license
Download [632.74KB]Silent Step 4 Click is a compact add-on board representing a completely integrated step motor driver solution. This board features the TMC2240, a smart integrated stepper driver from Analog Devices. The driver is based on a 256 micro-steps built-in indexer, two fully integrated H-Bridges, and non-dissipative integrated current sensing (ICS). The two H-Bridges can drive motors of up to 36V and 3A at max.
[learn more]Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.4
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 65 times
Not followed.
License: MIT license
Download [488.42KB]Charger Click is a compact add-on board providing a standalone battery charger and monitor. This board features Microchip's MCP73831, a miniature single-cell, fully integrated Li-Ion, Li-Polymer charge management controller. The charge voltage of the MCP73831 is set to 4.20V, and a charge current to 250mA with an external resistor. In addition, this Click board™ features the DS2438, a smart battery monitor that monitors the total amount of current going into and out of the battery.
[learn more]Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: Buck-Boost
Downloaded: 107 times
Not followed.
License: MIT license
Download [596.80KB]Buck-Boost 4 Click is a compact add-on board that contains a buck-boost DC/DC converter with four integrated MOSFETs. This board features the TPS55289, a buck-boost converter from Texas Instruments. It can deliver on its output voltages from 0.8 up to 22V, from the input voltage in a range of 3 up to 30V. The output voltage can be programmed in 10mV steps.
[learn more]Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.5
mikroSDK Library: 2.0.0.0
Category: LCD
Downloaded: 168 times
Not followed.
License: MIT license
Download [7.23KB]Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.7
mikroSDK Library: 2.0.0.0
Category: RTC
Downloaded: 59 times
Not followed.
License: MIT license
Download [8.89KB]Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.5
mikroSDK Library: 2.0.0.0
Category: Storage
Downloaded: 72 times
Not followed.
License: MIT license
Download [8.34KB]Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.7
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 88 times
Not followed.
License: MIT license
Download [9.23KB]