Use your forum account to login.

LOGIN

TOP Contributors

  1. MikroElektronika Team (436 codes)
  2. Shawon Shahryiar (246 codes)
  3. Alcides Ramos (96 codes)
  4. Dany (66 codes)
  5. O B (61 codes)
  6. MikroBUS.NET Team (35 codes)
  7. NART SCHINACKOW (34 codes)
  8. Alberto Trasimeni (25 codes)
  9. Roman Toropov (25 codes)
  10. Arezki YOUYOU (24 codes)

Most Downloaded

  1. Timer Calculator (77371 times)
  2. Network Ethernet Library (37711 times)
  3. FAT32 Library (36414 times)
  4. USB Device Library (28353 times)
  5. Network WiFi Library (27120 times)
  6. FT800 Library (19780 times)
  7. PID Library (18898 times)
  8. GSM click - Example (18497 times)
  9. microSD click - Example (15828 times)
  10. GPS click - Example (12694 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Example

TILT-n-SHAKE click

Rating:

Author: MikroElektronika Team

Last Updated: 2015-08-27

Category: Measurement

Downloaded: 426 times

Followed by: 3 users

TILT-n-SHAKE click carries Freescale’s MMA8491Q IC. It’s a multifunctional 3-axis digital accelerometer that can also be configured as a 45-degree Tilt sensor. As an accelerometer, it communicates with the target MCU through mikroBUS™ I2C pins (SCL, SDA).

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "TILT-n-SHAKE click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "TILT-n-SHAKE click" changes.

Do you want to report abuse regarding "TILT-n-SHAKE click".

  • Information
  • Comments (0)

Example Blog

TILT-n-SHAKE click board

TILT-n-SHAKE click board

Front and back view of TILT-n-SHAKE click board

View full image

TILT-n-SHAKE click carries Freescale’s MMA8491Q IC. It’s a multifunctional 3-axis digital accelerometer that can also be configured as a 45-degree Tilt sensor. As an accelerometer, it communicates with the target MCU through mikroBUS™ I2C pins (SCL, SDA). When configured as a Tilt sensor, the click board needs only one output pin — INT (interrupt). TILT-n-SHAKE click is designed to use a 3.3V power supply only.

Examples are written for :

-EasyMx PRO v7 for STM32 - STM32F107VC

TILT-n-SHAKE Schematic

TILT-n-SHAKE Schematic

Schematics of the TILT-n-SHAKE Click

View full image

ALSO FROM THIS AUTHOR

DC Motor 4 click

DC MOTOR 4 click is capable of driving motors between 4.5V and 36V. It carries the MAX14870 motor driver from Maxim Integrated. The click is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 click communicates with the target MCU over the following pins on the mikroBUS™ line: PWM, AN, CS, and INT.

[Learn More]

Lin Hall Click - Example

LIN HALL click, with its linear Hall sensor, outputs a signal that is proportional to the flux density of a magnetic field. The output signal will increase when a north magnetic field is applied, while a south magnetic field will cause it to decrease.

[Learn More]

16x9 click

16x9 G click contains a green LED matrix and the IS31FL3731 audio modulated matrix LED driver. The dimension of the LED matrix is 16x9. Each LED can be controlled individually – both for on/off control and light intensity.

[Learn More]