Use your forum account to login.

LOGIN

TOP Contributors

  1. MikroElektronika Team (452 codes)
  2. Shawon Shahryiar (246 codes)
  3. Alcides Ramos (97 codes)
  4. Dany (66 codes)
  5. O B (61 codes)
  6. MikroBUS.NET Team (35 codes)
  7. NART SCHINACKOW (34 codes)
  8. Alberto Trasimeni (25 codes)
  9. Roman Toropov (25 codes)
  10. Arezki YOUYOU (24 codes)

Most Downloaded

  1. Timer Calculator (78341 times)
  2. Network Ethernet Library (38043 times)
  3. FAT32 Library (37062 times)
  4. USB Device Library (28701 times)
  5. Network WiFi Library (27410 times)
  6. FT800 Library (20161 times)
  7. PID Library (19026 times)
  8. GSM click - Example (18596 times)
  9. microSD click - Example (15965 times)
  10. GPS click - Example (12784 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Library

Cap Extend Click

Rating:

Author: MikroElektronika Team

Last Updated: 2016-06-06

Category: Measurement

Downloaded: 353 times

Followed by: 1 user

Click – board with SX8633 low power capacitive touch button controller | MikroElektronika


Cap Extend click carries a SEMTECH SX8633 low power, capacitive button touch controller. It has 12 pins for connecting capacitive inputs (either touch-buttons or proximity sensors). Any sort of conductive object can be used as an input.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Cap Extend Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Cap Extend Click" changes.

Do you want to report abuse regarding "Cap Extend Click".

  • Information
  • Comments (1)

Library Blog

Cap Extend Front / Back Picture

Cap Extend Front / Back Picture

Cap Extend Front / Back Picture

View full image

Cap Extend click is a mikroBUS add-on board with a SEMTECH SX8633 low power, capacitive button touch controller. It has 12 pins for connecting capacitive inputs (either touch-buttons or proximity sensors). Any sort of conductive object can be used as an input. Additional 8 GPIO pins, available on the side-edges of the board, can be used as LED drivers. The SX8633 IC integrates a 10 bit ADC – a resolution high enough to support a wide variety of touch pad sizes and shapes to be used with the click. Cap Extend click communicates with the target MCU through the mikroBUS I2C interface, with additional functionality provided by RST and INT pins. Designed to use a 3.3V power supply only.  Applications Replacement of mechanical buttons with capacitive inputs (both in consumer products or industrial instrumentation)   Key features - 12 pins for connecting capacitive inputs - 8 GPIO pins - I2C interface - 3.3V power supply   Key benefits - Can be used for proximity sensing as well as capacitive buttons - Capable of sensing through overlay materials (up to 5mm thick) - No external components for sensor inputs required - Ready-to-use examples save development time

Cap Extend Click Schematic

Cap Extend Click Schematic

Cap Extend Click Schematic

View full image

ALSO FROM THIS AUTHOR

UNIQUE ID click

Unique ID click carries DS2401, an enhanced silicon serial number IC. The chip uses 1-wire communications for interfacing with the target board microcontroller.

[Learn More]

CO click - Example

This example demonstrates usage of the CO click board in mikroBUS form factor. This CO sensor is suitable for gas detecting equipment for Carbon Monoxide (CO). LCD shows PPM value of Carbon Monoxide (CO) concentration.

[Learn More]

mikromedia for STM32 M4 - Examples

Set of examples for mikromedia for STM32 M4.. Provided examples demonstrate working with mikromedia's various features and modules:

- Accelerometer
- MMC SD card
- MP3
- Serial Flash
- TFT
- Touch Panel
- USB UART

[Learn More]