EEPROM 5 click

EEPROM 5 Click is a compact add-on board that contains the highest-density memory solution. This board features the M95M04, the 4Mbit electrically erasable programmable memory organized as 524288 x 8 bits accessed through the SPI interface from STMicroelectronics.

click Product page

Click library

• Author : Stefan Ilic
• Date : Jul 2021.
• Type : SPI type

Software Support

We provide a library for the EEPROM5 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for EEPROM5 Click driver.

Standard key functions :

• eeprom5_cfg_setup Config Object Initialization function.

  void eeprom5_cfg_setup ( eeprom5_cfg_t *cfg );

• eeprom5_init Initialization function.

  err_t eeprom5_init ( eeprom5_t *ctx, eeprom5_cfg_t *cfg );

Example key functions :

• eeprom5_set_hold Enable hold operation function.

  void eeprom5_set_hold ( eeprom5_t *ctx, uint8_t en_hold );

• eeprom5_read_memory Read EEPROM memory function.

  void eeprom5_read_memory ( eeprom5_t *ctx, uint32_t addr, uint8_t *p_rx_data, uint8_t n_bytes );

• eeprom5_write_memory Write EEPROM memory function.

  void eeprom5_write_memory ( eeprom5_t *ctx, uint32_t addr, uint8_t *p_tx_data, uint8_t n_bytes );

Example Description

This is an example that demonstrates the use of the EEPROM 5 Click board.

The demo application is composed of two sections :

Application Init

Initialization driver enables SPI, also write log.

void application_init ( void ) 
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    eeprom5_cfg_t eeprom5_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    eeprom5_cfg_setup( &eeprom5_cfg );
    EEPROM5_MAP_MIKROBUS( eeprom5_cfg, MIKROBUS_1 );
    err_t init_flag  = eeprom5_init( &eeprom5, &eeprom5_cfg );
    if ( SPI_MASTER_ERROR == init_flag ) 
    {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );
        for ( ; ; );
    }
    log_printf( &logger, " - - - - - - - - - - - \r\n" );
    log_printf( &logger, " Disabling HOLD \r\n" );
    log_printf( &logger, " - - - - - - - - - - - \r\n" );
    eeprom5_set_hold( &eeprom5, EEPROM5_HOLD_DISABLE );
    Delay_ms ( 100 );
    log_printf( &logger, " Disabling Write Protection \r\n" );
    log_printf( &logger, " - - - - - - - - - - - \r\n" );
    eeprom5_set_write_protect( &eeprom5, EEPROM5_WRITE_PROTECT_DISABLE );
    Delay_ms ( 100 );
    log_info( &logger, " Application Task " );
    log_printf( &logger, " - - - - - - - - - - - \r\n" );
}

Application Task

In this example, we write and then read data from EEPROM memory. Results are being sent to the Usart Terminal where you can track their changes. All data logs write on USB uart changes approximately for every 5 sec.

void application_task ( void ) 
{
    eeprom5_enable_memory_write( &eeprom5, EEPROM5_WRITE_MEMORY_ENABLE );
    Delay_ms ( 10 );

    eeprom5_write_memory( &eeprom5, 14, demo_data, 9 );
    log_printf( &logger, " Write data : %s ", demo_data );
    log_printf( &logger, " - - - - - - - - - - - \r\n" );
    Delay_ms ( 100 );

    eeprom5_read_memory( &eeprom5, 14, read_data, 9 );
    log_printf( &logger, " Read data : %s ", read_data );
    log_printf( &logger, " - - - - - - - - - - - \r\n" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.EEPROM5

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.