We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Rating:
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 97 times
Not followed.
License: MIT license
Stepper 20 Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S580FNG, a two-phase bipolar stepping motor driver from Toshiba Semiconductor. Fabricated with the BiCD process, it supports a PWM constant-current control drive and steps resolution from full to 1/32 for less motor noise and smoother control. It has a wide operating voltage range of 8.2V to 44V with a maximum output current capacity of 1.28A, decay modes selection function, protection, and several anomaly detection indicators.
Do you want to subscribe in order to receive notifications regarding "Stepper 20 Click" changes.
Do you want to unsubscribe in order to stop receiving notifications regarding "Stepper 20 Click" changes.
Do you want to report abuse regarding "Stepper 20 Click".
DOWNLOAD LINK | RELATED COMPILER | CONTAINS |
---|---|---|
5175_stepper_20_click.zip [600.99KB] | mikroC AI for ARM GCC for ARM Clang for ARM mikroC AI for PIC mikroC AI for PIC32 XC32 GCC for RISC-V Clang for RISC-V mikroC AI for AVR mikroC AI for dsPIC XC16 |
|
Stepper 20 Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S580FNG, a two-phase bipolar stepping motor driver from Toshiba Semiconductor. Fabricated with the BiCD process, it supports a PWM constant-current control drive and steps resolution from full to 1/32 for less motor noise and smoother control. It has a wide operating voltage range of 8.2V to 44V with a maximum output current capacity of 1.28A, decay modes selection function, protection, and several anomaly detection indicators.
We provide a library for the Stepper 20 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
This library contains API for Stepper 20 Click driver.
stepper20_cfg_setup
Config Object Initialization function.
void stepper20_cfg_setup ( stepper20_cfg_t *cfg );
stepper20_init
Initialization function.
err_t stepper20_init ( stepper20_t *ctx, stepper20_cfg_t *cfg );
stepper20_default_cfg
Click Default Configuration function.
err_t stepper20_default_cfg ( stepper20_t *ctx );
stepper20_set_direction
This function sets the motor direction by setting the DIR pin logic state.
void stepper20_set_direction ( stepper20_t *ctx, uint8_t dir );
stepper20_drive_motor
This function drives the motor for the specific number of steps at the selected speed.
void stepper20_drive_motor ( stepper20_t *ctx, uint32_t steps, uint8_t speed );
stepper20_set_step_mode
This function sets the step mode resolution settings.
err_t stepper20_set_step_mode ( stepper20_t *ctx, uint8_t mode );
This example demonstrates the use of the Stepper 20 Click board by driving the motor in both directions for a desired number of steps.
The demo application is composed of two sections :
Initializes the driver and performs the Click default configuration.
void application_init ( void )
{
log_cfg_t log_cfg; /**< Logger config object. */
stepper20_cfg_t stepper20_cfg; /**< Click config object. */
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
stepper20_cfg_setup( &stepper20_cfg );
STEPPER20_MAP_MIKROBUS( stepper20_cfg, MIKROBUS_1 );
if ( I2C_MASTER_ERROR == stepper20_init( &stepper20, &stepper20_cfg ) )
{
log_error( &logger, " Communication init." );
for ( ; ; );
}
if ( STEPPER20_ERROR == stepper20_default_cfg ( &stepper20 ) )
{
log_error( &logger, " Default configuration." );
for ( ; ; );
}
log_info( &logger, " Application Task " );
}
Drives the motor clockwise for 200 full steps and then counter-clockiwse for 400 quarter steps with 2 seconds delay before changing the direction. All data is being logged on the USB UART where you can track the program flow.
void application_task ( void )
{
log_printf ( &logger, " Move 200 full steps clockwise \r\n\n" );
stepper20_set_step_mode ( &stepper20, STEPPER20_MODE_FULL_STEP );
stepper20_set_direction ( &stepper20, STEPPER20_DIR_CW );
stepper20_drive_motor ( &stepper20, 200, STEPPER20_SPEED_FAST );
Delay_ms ( 1000 );
Delay_ms ( 1000 );
log_printf ( &logger, " Move 400 quarter steps counter-clockwise \r\n\n" );
stepper20_set_step_mode ( &stepper20, STEPPER20_MODE_QUARTER_STEP );
stepper20_set_direction ( &stepper20, STEPPER20_DIR_CCW );
stepper20_drive_motor ( &stepper20, 400, STEPPER20_SPEED_VERY_FAST );
Delay_ms ( 1000 );
Delay_ms ( 1000 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
Other Mikroe Libraries used in the example:
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.