TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (392 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (123 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (140535 times)
  2. FAT32 Library (73024 times)
  3. Network Ethernet Library (58029 times)
  4. USB Device Library (48212 times)
  5. Network WiFi Library (43822 times)
  6. FT800 Library (43294 times)
  7. GSM click (30359 times)
  8. mikroSDK (28985 times)
  9. PID Library (27116 times)
  10. microSD click (26720 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Visual TFT/GLCD Project

Mikromedia Plus - STMP610 - show Touch Calibration Constants

Rating:

0

Author: Alexander Wolf

Last Updated: 2016-02-18

Package Version: 1.0.0.0

Category: TFT

Downloaded: 628 times

Followed by: 2 users

License: MIT license  

Programm reads Touch constants and shows them on screen. For Mikromedia Plus Board with STM610 Chip. Configure your Touch screen with that constants and disable Touch calibration every time you start your device.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Mikromedia Plus - STMP610 - show Touch Calibration Constants" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Mikromedia Plus - STMP610 - show Touch Calibration Constants" changes.

Do you want to report abuse regarding "Mikromedia Plus - STMP610 - show Touch Calibration Constants".

  • Information
  • Comments (0)
DOWNLOAD LINK RELATED COMPILER CONTAINS
mikroC PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc

Visual TFT/GLCD Project Blog

Blog currently doesn't exist!

ALSO FROM THIS AUTHOR

BNO055 BOSCH 9DOF Config and Read Example

0

I use the BNO055 for Drones and Balancing Robots. Its a Basic example in configuring and readig the chip. In combination with the Datasheet it should be adoptable to other languages than C for PIC32. If the crappy MikroE Exampe doesnt work, check this out. Check for correct PIN connections because I dont use mikroBus

[Learn More]

mikroBus Nucleo STM32 Shield

5

MikroBus adapter Shield for Nucleo. Nucleo Board can be programmed easy with microC for ARM without any programmer needed ( already on the Nucleo Board) Just let it produce by any PCB manufacturer like ITEAD on the PCB is: - microSd Card adapter - USB - 2x mikroBus Sockets - 2x LEDs - 2x User Buttons - x Jumpers for current sensing

[Learn More]

Power PIC32 down into SLEEP mode and wake up via RTC ALARM by INTERRUPT

5

This is the Program structure of a power saving example. Pic32 starts and works at 8Mhz without PLL for low current consumption. When shutting down, 8Mhz crystal and all Modules are deaktivated but SOSC is enabled to be able to wake up CPU by RTC ALARM Interrupt.

[Learn More]