We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.7
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 86 times
Not followed.
License: MIT license
Download [9.23KB]
Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.5
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 80 times
Not followed.
License: MIT license
Download [8.63KB] Author: MIKROE
Last Updated: 2024-07-09
Package Version: 2.0.0.7
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 79 times
Not followed.
License: MIT license
Download [9.01KB] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 93 times
Not followed.
License: MIT license
Download [514.62KB]CAN FD 7 Click is a compact add-on board that contains a CAN transceiver that supports both CAN and CAN FD protocols. This board features the TCAN1462, an automotive fault-protected CAN FD transceiver from Texas Instruments. It is a high-speed Controller Area Network (CAN) transceiver that meets the ISO 11898-2:2016 high-speed CAN specification and the CiA 601-4 signal improvement capability (SIC) specification.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 139 times
Not followed.
License: MIT license
Download [572.01KB]CAN Isolator 3 Click is a compact add-on board that provides isolated CAN communication. This board features the MAX14882, an isolated CAN transceiver with an integrated transformer driver from Analog Devices. It is galvanically isolated between the device's CAN-protocol controller side (TDX, RDX) and the physical wires of the CAN network (CANH, CANL) cable-side/bus-side of the transceiver.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 94 times
Not followed.
License: MIT license
Download [1.02MB]MCP2517FD Click is a complete CAN solution which carries the MCP2517FD CAN FD controller and ATA6563 high-speed CAN transceiver from Microchip, as well as a DB9 9-pin connector.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 136 times
Not followed.
License: MIT license
Download [1.03MB]MCP2518FD Click is a compact add-on board representing a complete CAN solution used as a control node in a CAN network. This board features the MCP2518FD, an external CAN FD controller with an SPI interface, and a high-speed CAN transceiver, the ATA6563, both from Microchip. The ATA6563, a low-level physical layer IC (PHY), provides a physical connection with the CAN bus itself, while the CAN controller MCP2518FD represents an interface between the MCU and the PHY. It features three operating modes with dedicated fail-safe features, remote wake-up via CAN, and ideally passive behavior when powered off on the CAN bus. This Click board™ is suitable for developing a wide range of automotive diagnostic applications, even on MCUs that do not natively support CAN interface.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.8
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 105 times
Not followed.
License: MIT license
Download [505.22KB]CAN Isolator 2 Click is a compact add-on board that provides isolated CAN communication. This board features the ISO1042, an isolated CAN transceiver from Texas Instruments. This galvanically-isolated CAN transceiver meets the ISO11898-2 specifications and offers a +/-70V DC bus fault protection, along with the +/-30V of common mode voltage range. The transceiver supports two CAN modes, with speeds of up to 1Mbps in Classic CAN and flexible data rate (FD) CAN, which allows much faster transfer of payload compared to the classic CAN with up to 5Mbps.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 383 times
Not followed.
License: MIT license
Download [1.03MB]MCP251863 Click is a compact add-on board representing a complete CAN solution used as a control node in a CAN network. This board features the MCP251863, IC representing a compact solution with a controller and a transceiver in one package, the MCP2518FD and ATA6563 from Microchip. The ATA6563, a low-level physical layer IC (PHY), provides a physical connection with the CAN bus itself, while the CAN controller MCP2518FD represents an interface between the MCU and the PHY. It features three operating modes with dedicated fail-safe features, remote wake-up via CAN, and ideally passive behavior when powered off on the CAN bus. This Click board™ is suitable for developing a wide range of automotive diagnostic applications, even on MCUs that don’t support CAN interface.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 147 times
Not followed.
License: MIT license
Download [369.80KB]ISO 9141 Click is a compact add-on board that contains a monolithic bus driver with ISO 9141 interface. This board features the L9637, a monolithic integrated circuit containing standard ISO 9141 compatible interface functions from ST Microelectronics.
[learn more] 
