Code Categories

All codes (5055)

TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (142087 times)
  2. FAT32 Library (75339 times)
  3. Network Ethernet Library (59508 times)
  4. USB Device Library (49528 times)
  5. Network WiFi Library (45310 times)
  6. FT800 Library (44942 times)
  7. GSM click (31451 times)
  8. mikroSDK (30476 times)
  9. microSD click (27805 times)
  10. PID Library (27625 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Example

MPU IMU click with TFT - Example for PIC32

Rating:

0

Author: Alexander Wolf

Last Updated: 2016-02-23

Package Version: 1.0.0.1

Example: 1.0.0.0

Category: Measurement

Downloaded: 613 times

Followed by: 1 user

License: MIT license  

For PIC32 modified code from Mikroelektronikas MPU example.\x0D\x0A
Using TFT drwawing a waterlevel and UART for Output data on FusionBoard.\x0D\x0A
This may help People using I2C PIC32 and EasyPicFusionV7.\x0D\x0A
Don't Forget Pull UP on SCL and SDA :)

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "MPU IMU click with TFT - Example for PIC32" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "MPU IMU click with TFT - Example for PIC32" changes.

Do you want to report abuse regarding "MPU IMU click with TFT - Example for PIC32".

  • Information
  • Comments (0)

Example Blog

TFT screen

TFT screen

Gyroscope Screen with water level

View full image

ALSO FROM THIS AUTHOR

BNO055 BOSCH 9DOF Config and Read Example

0

I use the BNO055 for Drones and Balancing Robots. Its a Basic example in configuring and readig the chip. In combination with the Datasheet it should be adoptable to other languages than C for PIC32. If the crappy MikroE Exampe doesnt work, check this out. Check for correct PIN connections because I dont use mikroBus

[Learn More]

EEPROM 3 click AT24CM02 and other 16 Bit Adress EEPROM and FRAM

0

simple example for Read/write Byte for AT24CM02 EEPROM. Even the example is in C and for PIC32, it should be easy to adopt to other languages, since its a complete project. If AdressBits are changed, it also works with other 16 Bit adress I2C EEPROM &amp; FRAM

[Learn More]

Power PIC32 down into SLEEP mode and wake up via RTC ALARM by INTERRUPT

5

This is the Program structure of a power saving example. Pic32 starts and works at 8Mhz without PLL for low current consumption. When shutting down, 8Mhz crystal and all Modules are deaktivated but SOSC is enabled to be able to wake up CPU by RTC ALARM Interrupt.

[Learn More]

embeddedwiki libstock