Code Categories

All codes (5055)

TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141994 times)
  2. FAT32 Library (75226 times)
  3. Network Ethernet Library (59464 times)
  4. USB Device Library (49483 times)
  5. Network WiFi Library (45264 times)
  6. FT800 Library (44865 times)
  7. GSM click (31411 times)
  8. mikroSDK (30398 times)
  9. microSD click (27775 times)
  10. PID Library (27613 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Project

BNO055 BOSCH 9DOF Config and Read Example

Rating:

0

Author: Alexander Wolf

Last Updated: 2016-06-28

Package Version: 1.0.0.0

Category: Measurement

Downloaded: 716 times

Not followed.

License: MIT license  

I use the BNO055 for Drones and Balancing Robots. Its a Basic example in configuring and readig the chip. In combination with the Datasheet it should be adoptable to other languages than C for PIC32. If the crappy MikroE Exampe doesnt work, check this out. Check for correct PIN connections because I dont use mikroBus

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "BNO055 BOSCH 9DOF Config and Read Example" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "BNO055 BOSCH 9DOF Config and Read Example" changes.

Do you want to report abuse regarding "BNO055 BOSCH 9DOF Config and Read Example".

  • Information
  • Comments (0)
Download

Download All [317.15KB]

DOWNLOAD LINK RELATED COMPILER CONTAINS
1467112333_bno055_bosch_9do_mikroc_pic32.zip [316.55KB] mikroC PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc

Project Blog

Blog currently doesn't exist!

ALSO FROM THIS AUTHOR

PIC32 MX SD Card Bootloader

9

This is a SD Card Bootloader for PIC32 MX. The hard work making this work did M. Hooper. I added FAT32 and some little things to make it work on Fusion V7 board. Attached is a PDF manual which describes more: 1. flash bootloader to your MCU 2. add some lines to your Application 3. rename and save hex file on sd card 4. start and push button RB0

[Learn More]

mikroBus Nucleo STM32 Shield

5

MikroBus adapter Shield for Nucleo. Nucleo Board can be programmed easy with microC for ARM without any programmer needed ( already on the Nucleo Board) Just let it produce by any PCB manufacturer like ITEAD on the PCB is: - microSd Card adapter - USB - 2x mikroBus Sockets - 2x LEDs - 2x User Buttons - x Jumpers for current sensing

[Learn More]

EEPROM 3 click AT24CM02 and other 16 Bit Adress EEPROM and FRAM

0

simple example for Read/write Byte for AT24CM02 EEPROM. Even the example is in C and for PIC32, it should be easy to adopt to other languages, since its a complete project. If AdressBits are changed, it also works with other 16 Bit adress I2C EEPROM &amp; FRAM

[Learn More]

embeddedwiki libstock