Code Categories

All codes (5055)

TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (142090 times)
  2. FAT32 Library (75349 times)
  3. Network Ethernet Library (59521 times)
  4. USB Device Library (49542 times)
  5. Network WiFi Library (45331 times)
  6. FT800 Library (44956 times)
  7. GSM click (31461 times)
  8. mikroSDK (30499 times)
  9. microSD click (27821 times)
  10. PID Library (27628 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Library

C Meter click

Rating:

1

Author: MIKROE

Last Updated: 2016-10-25

Package Version: 1.0.0.0

Category: Measurements

Downloaded: 1326 times

Not followed.

License: MIT license  

C Meter click is a mikroBUS add-on board with circuitry for measuring the value of capacitors. The design is based on a NE-555 timer/square-wave generator.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "C Meter click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "C Meter click" changes.

Do you want to report abuse regarding "C Meter click".

  • Information
  • Comments (1)

Library Blog

Product Page
Learn Page
Manual Page
C Meter click

C Meter click

C Meter click Front and Back picture.

View full image

C Meter click is a mikroBUS add-on board with circuitry for measuring the value of capacitors. The design is based on a NE-555 timer/square-wave generator. The chip is implemented in an astable multivibrator circuit with fixed resistors and adjustable capacitors. 


The board has four different-sized plates for placing SMD capacitors (covering standard SMD packaging dimensions) as well as a socket for inserting a thru hole capacitor. 


The board outputs a square wave frequency through the INT pin. Depending on the capacitor placed on the board, the value of this frequency changes. The value of a capacitor can be inferred using a simple algorithm (shown in the Libstock code example). 


Onboard screw terminals are placed to allow the click to be used with multimeter probes. 
C Meter click is designed to use a 5V power supply, but can work with either 3.3V or 5V logic levels.

C Meter click

C Meter click

C Meter click Shematic Picture.

View full image

ALSO FROM THIS AUTHOR

4DotMatrix click

6

4Dot-Matrix R click allows you to display 4 characters of 5x7 dot size. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface.

[Learn More]

4x4 RGB click

1

4x4 RGB click carries a matrix of 16 RGB LEDs and a MCP1826 low dropout regulator. The LED matrix is connected to the target board microcontroller through the mikroBUS RST pin. The board uses either a 3.3V or 5V power supply.

[Learn More]

HTU21D Click

0

The application is composed of two sections.

[Learn More]

embeddedwiki libstock