TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (402 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (129 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (140778 times)
  2. FAT32 Library (73364 times)
  3. Network Ethernet Library (58201 times)
  4. USB Device Library (48387 times)
  5. Network WiFi Library (43982 times)
  6. FT800 Library (43541 times)
  7. GSM click (30471 times)
  8. mikroSDK (29177 times)
  9. PID Library (27173 times)
  10. microSD click (26848 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

Pressure 3 click

Rating:

1

Author: MIKROE

Last Updated: 2019-04-03

Package Version: 1.0.0.1

mikroSDK Library: 1.0.0.0

Category: Pressure

Downloaded: 4846 times

Not followed.

License: MIT license  

Pressure 3 click is a mikroBUS add-on board that carries an Infineon DPS310 digital barometric pressure sensor. Pressure 3 click has both I2C and SPI outputs. The four interface configuration buttons are soldered to mikroBUSâ„¢ I2C pins by default. The click uses a 3.3V power supply.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Pressure 3 click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Pressure 3 click" changes.

Do you want to report abuse regarding "Pressure 3 click".

  • mikroSDK Library 2.0.0.0
  • Comments (2)
DOWNLOAD LINK RELATED COMPILER CONTAINS
mikroBasic PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc

mikroSDK Library Blog

Pressure 3 click

Pressure 3 click

Front and back view of the Pressure 3 click board

View full image

Library Description

The library covers all the necessary functions to control Pressure 3 Click board. Library performs the communication with the device via I2C or SPI driver by writing to registers and by reading from registers. The library has generic write and reads function, get measurements function, get the temperature and pressure data from the register, the function for reading factory calibration, for sets configuration, etc. Function who gets temperature and pressure also read factory calibration and converts temperature data to degree Celsius [ °C ] and pressure value to mbar .

Key functions:

  • void pressure3_getTemperaturePressure( float *temperature, float *presure ) - Get the Temperature and Pressure value function.
  • void pressure3_softReset() - Soft reset function.
  • void pressure3_setOperatingMode( uint8_t operationMode ) - Set the sensor operating mode function.

Examples description

The application is composed of three sections:

  • System Initialization - Initializes GPIO, I2C or SPI, and LOG structures, sets INT pins as input, CS pin as output and start to write log.
  • Application Initialization -  Initialization driver enables - I2C or SPI, set default configuration and start to write log.
  • Application Task - (code snippet) This is an example which demonstrates the use of Pressure 3 Click board. Measured pressure and temperature data from the DPS310 sensor on Pressure 3 click board. Results are being sent to the Usart Terminal where you can track their changes. All data logs write on usb uart changes for every 3 sec.
void applicationTask() 
{
    pressure3_getTemperaturePressure( &temperature, &pressure );
    
    mikrobus_logWrite( " Pressure   : ", _LOG_TEXT );
    FloatToStr( pressure, logText );
    mikrobus_logWrite( logText, _LOG_TEXT );
    mikrobus_logWrite( " mbar", _LOG_LINE );

    mikrobus_logWrite( " Temperature: ", _LOG_TEXT );
    FloatToStr( temperature, logText );
    mikrobus_logWrite( logText, _LOG_TEXT );
    mikrobus_logWrite( degCel, _LOG_LINE );
    mikrobus_logWrite( "----------------------------", _LOG_LINE );

    Delay_1sec();
    Delay_1sec();
    Delay_1sec();
}      

Other mikroE Libraries used in the example:

  • SPI or I2C
  • UART​
  • Conversion

Additional notes and informations

Depending on the development board you are using, you may need USB UART clickUSB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message

ALSO FROM THIS AUTHOR

Motion 2 click

5

Motion 2 Click is a based on EKMC1607112, PIR motion sensor from Panasonic Corporation that's used as human motion detector. Also it is featured with TLP241A photorelay from Toshiba that is used to provide a reinforced galvanic isolation for the external signals used to drive some external high power electronic equipment when motion is detected.

[Learn More]

RS485 6 click

5

RS485 6 Click is offers a half-duplex RS-485 communication with integrated surge protection, which can be used as an interface between the TTL level UART and the RS485 communication bus. It is based on THVD1429DT, a transceiver from Texas Instruments with signaling rate of up to 20 Mbps.

[Learn More]

Brushless 6 click

0

Brushless 6 click is designed to drive a three-phase sensorless, brushless motor, also known as the BLDC motor. The motor rotation is controlled by receiving driving commands via the incoming PWM signal.

[Learn More]