TOP Contributors

  1. MIKROE (2751 codes)
  2. Alcides Ramos (372 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (118 codes)
  5. Bugz Bensce (90 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (139059 times)
  2. FAT32 Library (71589 times)
  3. Network Ethernet Library (56988 times)
  4. USB Device Library (47330 times)
  5. Network WiFi Library (43006 times)
  6. FT800 Library (42297 times)
  7. GSM click (29774 times)
  8. mikroSDK (27874 times)
  9. PID Library (26858 times)
  10. microSD click (26129 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

SPI Isolator click

Rating:

5

Author: MIKROE

Last Updated: 2019-07-30

Package Version: 1.0.0.0

mikroSDK Library: 1.0.0.0

Category: SPI

Downloaded: 3190 times

Not followed.

License: MIT license  

SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface (SPI), from Analog Devices. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI interface.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "SPI Isolator click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "SPI Isolator click" changes.

Do you want to report abuse regarding "SPI Isolator click".

  • mikroSDK Library 2.0.0.0
  • Comments (0)
DOWNLOAD LINK RELATED COMPILER CONTAINS
mikroBasic PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc

mikroSDK Library Blog

Library Description

The library covers all the necessary functions to control SPI Isolator click board. Library performs the communication with the device via SPI protocol by writing to registers and by reading from registers.

Key functions:

  • void spiisolator_writeByte( uint8_t regAddress, uint8_t writeCmd, uint8_t writeData ) - Write the byte of data function.
  • uint16_t spiisolator_readData( uint8_t regAddress, uint8_t readCmd ) - Read 16-bit data function.
  • void spiisolator_writeBytes( uint8_t regAddress, uint8_t writeCmd, uint8_t *writeData, uint16_t nBytes ) - Sequential write function.

Examples description

The application is composed of the three sections :

  • System Initialization - Initializes GPIO, SPI, and LOG structures, set CS pin as output and start to write log.
  • Application Initialization - Initialization driver enables - SPI, set default configuration, also write log.
  • Application Task - This is an example which demonstrates the use of SPI Isolator Click board. In this example, we measured pressure and temperature data from the DPS310 sensor on Pressure 3 click board. Results are being sent to the Usart Terminal where you can track their changes. All data logs write on usb uart changes for every 3 sec.
void applicationTask()
{
    pressure3_getCoefficients0();
    pressure3_getCoefficients1();
    spiisolator_getTemperaturePressure();

    mikrobus_logWrite( " Pressure   : ", _LOG_TEXT );
    FloatToStr( pressure, logText );
    mikrobus_logWrite( logText, _LOG_TEXT );
    mikrobus_logWrite( " mbar", _LOG_LINE );

    mikrobus_logWrite( " Temperature: ", _LOG_TEXT );
    FloatToStr( temperature, logText );
    mikrobus_logWrite( logText, _LOG_TEXT );
    mikrobus_logWrite( degCel, _LOG_LINE );
    mikrobus_logWrite( "----------------------------", _LOG_LINE );

    Delay_1sec();
    Delay_1sec();
    Delay_1sec();
}

Additional Functions :

  • void pressure3_getCoefficients0() - Get the coefficients value for calculation function.
  • void pressure3_getCoefficients1() - Get the coefficients value for calculation function.
  • void spiisolator_getTemperaturePressure() - Get the Temperature and Pressure value function.

Other mikroE Libraries used in the example:

  • SPI
  • UART
  • Conversions

Additional notes and informations

Depending on the development board you are using, you may need USB UART clickUSB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

ALSO FROM THIS AUTHOR

Barcode click

5

Barcode click is a very fast and agile barcode scanner on a click board, which is compliant with a wide range of different 1D and 2D barcode protocols.

[Learn More]

EERAM 2 Click

0

EERAM 2 Click is a standalone serial SRAM memory that includes shadow non-volatile backup. EERAM uses a small external capacitor to provide the energy needed to move the contents of the SRAM to the non-volatile cells when system power is lost.

[Learn More]

RS485 Isolator 2 click

5

RS485 Isolator 2 Click features ADM2867E a 5.7 kV rms signal and power isolated full duplex RS-485 transceiver. The device also features cable invert pins, allowing the user to quickly correct reversed cable connection on A, B, Y, and Z bus pins while maintaining receiver full receiver fail-safe performance.

[Learn More]