We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Rating:
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.16
mikroSDK Library: 2.0.0.0
Category: Temperature & humidity
Downloaded: 194 times
Not followed.
License: MIT license
If you need a temperature sensor and relay in one device, you should look no further than Thermostat Click. It can be used to measure environmental temperature and to directly switch ON/OFF cooling and heating devices, performing all the functions of a thermostat.
Do you want to subscribe in order to receive notifications regarding "Thermostat Click" changes.
Do you want to unsubscribe in order to stop receiving notifications regarding "Thermostat Click" changes.
Do you want to report abuse regarding "Thermostat Click".
DOWNLOAD LINK | RELATED COMPILER | CONTAINS |
---|---|---|
3431_thermostat_click.zip [559.01KB] | mikroC AI for ARM GCC for ARM Clang for ARM mikroC AI for PIC mikroC AI for PIC32 XC32 GCC for RISC-V Clang for RISC-V mikroC AI for AVR mikroC AI for dsPIC XC16 |
|
If you need a temperature sensor and relay in one device, you should look no further than Thermostat Click.
We provide a library for the Thermostat Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.
This library contains API for Thermostat Click driver.
Config Object Initialization function.
void thermostat_cfg_setup ( thermostat_cfg_t *cfg );
Initialization function.
THERMOSTAT_RETVAL thermostat_init ( thermostat_t ctx, thermostat_cfg_t cfg );
Generic read 16-bit data function.
uint16_t thermostat_read_data( thermostat_t *ctx, uint8_t reg_address );
Get temperature in degrees Celsius.
float thermostat_get_temperature( thermostat_t *ctx );
Convert temperature in degrees Celsius to Fahrenheit.
float thermostat_convert_fahrenheit( thermostat_t *ctx, float temp_celsius );
Set configuration function.
void thermostat_set_configuration( thermostat_t *ctx, uint16_t config_value );
Set temperature hysterezis function
void thermostat_set_temp_hyst( thermostat_t *ctx, int8_t temp_hyst );
Set referent temperature function.
void thermostat_set_temp_ref( thermostat_t *ctx, int8_t temp_ref );
Soft reset function.
void thermostat_soft_reset( thermostat_t *ctx );
Set on thermal switch function
void thermostat_switch_on( thermostat_t *ctx );
Set off thermal switch function
void thermostat_switch_off( thermostat_t *ctx );
Thermostat enabled function.
void thermostat_enable( thermostat_t *ctx );
Thermostat disabled function.
void thermostat_disable( thermostat_t *ctx );
This application regulates value of temperature.
The demo application is composed of two sections :
Initialization driver enable's - I2C, soft reset sesnor, set default configuration and start write log.
void application_init ( void )
{
log_cfg_t log_cfg;
thermostat_cfg_t cfg;
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, "---- Application Init ----" );
// Click initialization.
thermostat_cfg_setup( &cfg );
THERMOSTAT_MAP_MIKROBUS( cfg, MIKROBUS_1 );
thermostat_init( &thermostat, &cfg );
thermostat_soft_reset( &thermostat );
Delay_ms ( 100 );
log_printf( &logger, " Configuration \r\n");
thermostat_set_configuration( &thermostat, THERMOSTAT_DEFAULT_CONFIG );
Delay_ms ( 100 );
log_printf( &logger, "----------------------\r\n" );
}
This is a example which demonstrates the use of Thermostat Click board.
void application_task ( void )
{
float temperature;
float limit_max = 25.0;
float limit_min = 15.0;
temperature = thermostat_get_temperature( &thermostat );
log_printf( &logger, " Temperature : %.2f \r\n", temperature );
if ( ( temperature < limit_max ) && ( temperature > limit_min ) )
{
thermostat_switch_on( &thermostat );
}
else
{
thermostat_switch_off( &thermostat );
log_printf( &logger, "----------------------\r\n" );
}
Delay_ms ( 1000 );
Delay_ms ( 1000 );
}
The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.
Other mikroE Libraries used in the example:
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.