TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141825 times)
  2. FAT32 Library (74956 times)
  3. Network Ethernet Library (59317 times)
  4. USB Device Library (49308 times)
  5. Network WiFi Library (45108 times)
  6. FT800 Library (44676 times)
  7. GSM click (31287 times)
  8. mikroSDK (30215 times)
  9. microSD click (27664 times)
  10. PID Library (27564 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

H-Bridge 7 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.14

mikroSDK Library: 2.0.0.0

Category: Brushed

Downloaded: 352 times

Not followed.

License: MIT license  

H-Bridge 7 Click features flexible motor driver IC for a wide variety of applications, labeled as the DRV8876N. This Click board™ integrates an N-channel H-bridge, charge pump regulator, and protection circuitry. The charge pump improves efficiency by allowing for both high-side and low-side N-channels MOSFETs and 100% duty cycle support. This IC allows the H-Bridge 7 Click to achieve ultra-low quiescent current draw by shutting down most of the internal circuitry with his low-power sleep mode.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "H-Bridge 7 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "H-Bridge 7 Click" changes.

Do you want to report abuse regarding "H-Bridge 7 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


H-Bridge 7 Click

H-Bridge 7 Click features flexible motor driver IC for a wide variety of applications, labeled as the DRV8876N. This Click board™ integrates an N-channel H-bridge, charge pump regulator, and protection circuitry. The charge pump improves efficiency by allowing for both high-side and low-side N-channels MOSFETs and 100% duty cycle support. This IC allows the H-Bridge 7 Click to achieve ultra-low quiescent current draw by shutting down most of the internal circuitry with his low-power sleep mode.

hbridge7_click.png

Click Product page


Click library

  • Author : MikroE Team
  • Date : Jun 2020.
  • Type : GPIO type

Software Support

We provide a library for the Hbridge7 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for Hbridge7 Click driver.

Standard key functions :

  • Config Object Initialization function.

    void hbridge7_cfg_setup ( hbridge7_cfg_t *cfg );

  • Initialization function.

    HBRIDGE7_RETVAL hbridge7_init ( hbridge7_t ctx, hbridge7_cfg_t cfg );

Example key functions :

  • Set motor control.

    void hbridge7_motor_control ( hbridge7_t *ctx, uint8_t ctrl );

  • Get Fault pin state.

    uint8_t hbridge7_get_fault_state ( hbridge7_t *ctx );

Examples Description

This example demonstrates the use of H-Bridge 7 Click board.

The demo application is composed of two sections :

Application Init

Initializes the driver and makes an initial log.


void application_init ( void )
{
    log_cfg_t log_cfg;
    hbridge7_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info(&logger, "---- Application Init ----");

    //  Click initialization.

    hbridge7_cfg_setup( &cfg );
    HBRIDGE7_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    hbridge7_init( &hbridge7, &cfg );
}

Application Task

Drives the motor in the forward direction for 5 seconds, then pulls brake for 2 seconds, and after that drives it in the reverse direction for 5 seconds, and finally, disconnects the motor for 2 seconds. Each step will be logged on the USB UART where you can track the program flow.


void application_task ( void )
{
    log_printf( &logger, "The motor turns forward! \r\n" );
    hbridge7_motor_control( &hbridge7, HBRIDGE7_MOTOR_FORWARD );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf( &logger, "Pull brake! \r\n" );
    hbridge7_motor_control( &hbridge7, HBRIDGE7_MOTOR_BRAKE );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf( &logger, "The motor turns in reverse! \r\n" );
    hbridge7_motor_control( &hbridge7, HBRIDGE7_MOTOR_REVERSE );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf( &logger, "The motor is disconnected (High-Z)!  \r\n" );
    hbridge7_motor_control( &hbridge7, HBRIDGE7_MOTOR_SLEEP );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}   

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.Hbridge7

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

IR reflect Click

0

IR reflect Click carries a GP2S700HCP reflective photointerrupter and an onboard potentiometer. On this type of photointerrupter the infrared emitter and receiver are facing the same direction.

[Learn More]

ProxFusion click

5

ProxFusion click is a multifunctional capacitive and Hall-effect sensor device. This click can detect touch by using two onboard sensor pads, and it can sense a rotation angle of a magnetic field, parallel with the surface of the click board.

[Learn More]

Proximity 18 Click

0

Proximity 18 Click is a compact add-on board that contains a close-range proximity sensing solution. This board features the VCNL3036X01, a high-resolution digital proximity sensor from Vishay Semiconductors. Besides the proximity sensor, the VCNL3036X01 also integrates a mux and a driver for three external LEDs, which are located near the chip on the board, photodiodes, amplifiers, and analog to digital converting circuits into a single chip by CMOS process. It allows absolute distance measurement, whatever the target color and reflectance, providing an accurate range of up to 50cm.

[Learn More]