TOP Contributors

  1. MIKROE (2751 codes)
  2. Alcides Ramos (372 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (118 codes)
  5. Bugz Bensce (90 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (139060 times)
  2. FAT32 Library (71592 times)
  3. Network Ethernet Library (56989 times)
  4. USB Device Library (47330 times)
  5. Network WiFi Library (43006 times)
  6. FT800 Library (42297 times)
  7. GSM click (29777 times)
  8. mikroSDK (27874 times)
  9. PID Library (26858 times)
  10. microSD click (26129 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

M-Bus Slave Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.15

mikroSDK Library: 2.0.0.0

Category: RS232

Downloaded: 217 times

Not followed.

License: MIT license  

M-Bus Slave Click is a Click board™ equipped with the TSS721A, a single chip transceiver developed by Texas Instruments for Meter-Bus applications according to EN1434-3 standard. The connection to the bus is polarity independent and serves as a slave node in the system. M-Bus Slave Click has full galvanic isolation with optocouplers to improve the reliability of the whole circuit.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "M-Bus Slave Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "M-Bus Slave Click" changes.

Do you want to report abuse regarding "M-Bus Slave Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


M-Bus Slave Click

M-Bus Slave Click is a Click board™ equipped with the TSS721A, a single chip transceiver developed by Texas Instruments for Meter-Bus applications according to EN1434-3 standard. The connection to the bus is polarity independent and serves as a slave node in the system. M-Bus Slave Click has full galvanic isolation with optocouplers to improve the reliability of the whole circuit.

mbusslave_click.png

Click Product page


Click library

  • Author : MikroE Team
  • Date : Jun 2020.
  • Type : UART type

Software Support

We provide a library for the MBusSlave Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for MBusSlave Click driver.

Standard key functions :

  • Config Object Initialization function.

    void mbusslave_cfg_setup ( mbusslave_cfg_t *cfg );

  • Initialization function.

    MBUSSLAVE_RETVAL mbusslave_init ( mbusslave_t ctx, mbusslave_cfg_t cfg );

Example key functions :

  • Generic write function.

    void mbusslave_generic_write ( mbusslave_t ctx, char data_buf, uint16_t len );

  • Generic read function.

    int32_t mbusslave_generic_read ( mbusslave_t ctx, char data_buf, uint16_t max_len );

Examples Description

This example reads and processes data from M-Bus Slave clicks.

The demo application is composed of two sections :

Application Init

Initializes the driver.


void application_init ( void )
{
    log_cfg_t log_cfg;
    mbusslave_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );
    Delay_ms ( 100 );

    //  Click initialization.

    mbusslave_cfg_setup( &cfg );
    MBUSSLAVE_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    mbusslave_init( &mbusslave, &cfg );
    Delay_ms ( 100 );
}

Application Task

Depending on the selected mode, it reads all the received data or sends the desired message every 2 seconds.


void application_task ( void )
{
#ifdef DEMO_APP_RECEIVER
    mbusslave_process( );
#endif    

#ifdef DEMO_APP_TRANSMITTER
    mbusslave_generic_write( &mbusslave, TEXT_TO_SEND, strlen( TEXT_TO_SEND ) );
    log_info( &logger, "---- Data sent ----" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
#endif  
}

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.MBusSlave

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

I2C Extend 2 click

5

I2C Extend 2 Click is a compact add-on board suitable for I2C communication bus extension. This board features the PCA9615, a 2-channel multipoint differential I2C bus buffer with hot-swap logic from NXP Semiconductors.

[Learn More]

Secure 4 Click

0

Secure 4 click includes the ATECC608A, a secure CryptoAuthenticatio device from Microchip, which is equipped with an EEPROM array which can be used for storing of up to 16 keys, certificates, consumption logging, security configurations and other types of secure data.

[Learn More]

TILT-n-SHAKE click

5

TILT-n-SHAKE click carries Freescale’s MMA8491Q IC. It’s a multifunctional 3-axis digital accelerometer that can also be configured as a 45-degree Tilt sensor. As an accelerometer, it communicates with the target MCU through mikroBUS™ I2C pins (SCL, SDA).

[Learn More]