TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141683 times)
  2. FAT32 Library (74742 times)
  3. Network Ethernet Library (59203 times)
  4. USB Device Library (49219 times)
  5. Network WiFi Library (44990 times)
  6. FT800 Library (44518 times)
  7. GSM click (31195 times)
  8. mikroSDK (30087 times)
  9. microSD click (27578 times)
  10. PID Library (27537 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

nvSRAM 2 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.14

mikroSDK Library: 2.0.0.0

Category: SRAM

Downloaded: 330 times

Not followed.

License: MIT license  

nvSRAM 2 Click is a compact add-on board that contains the most reliable nonvolatile memory. This board features the CY14B101Q, a 1Mbit nvSRAM organized as 128K words of 8 bits each with a nonvolatile element in each memory cell from Cypress Semiconductor. The embedded nonvolatile elements incorporate the QuantumTrap technology and provide highly reliable nonvolatile storage of data. Data transfer, initiated by the user through SPI commands, from SRAM to the nonvolatile elements takes place automatically at Power-Down. On the other hand, during the Power-Up, data is restored to the SRAM from the nonvolatile memory. This Click board™ is suitable for all applications that require fast access and high reliability of stored data, and unlimited endurance.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "nvSRAM 2 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "nvSRAM 2 Click" changes.

Do you want to report abuse regarding "nvSRAM 2 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


nvSRAM 2 Click

nvSRAM 2 Click is a compact add-on board that contains the most reliable nonvolatile memory. This board features the CY14B101Q, a 1Mbit nvSRAM organized as 128K words of 8 bits each with a nonvolatile element in each memory cell from Cypress Semiconductor. The embedded nonvolatile elements incorporate the QuantumTrap technology and provide highly reliable nonvolatile storage of data. Data transfer, initiated by the user through SPI commands, from SRAM to the nonvolatile elements takes place automatically at Power-Down. On the other hand, during the Power-Up, data is restored to the SRAM from the nonvolatile memory. This Click board™ is suitable for all applications that require fast access and high reliability of stored data, and unlimited endurance.

nvsram2_click.png

Click Product page


Click library

  • Author : Jelena Milosavljevic
  • Date : Jul 2021.
  • Type : SPI type

Software Support

We provide a library for the nvSRAM2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for nvSRAM2 Click driver.

Standard key functions :

  • nvsram2_cfg_setup Config Object Initialization function.

    void nvsram2_cfg_setup ( nvsram2_cfg_t *cfg );
  • nvsram2_init Initialization function.

    err_t nvsram2_init ( nvsram2_t *ctx, nvsram2_cfg_t *cfg );
  • nvsram2_default_cfg Click Default Configuration function.

    err_t nvsram2_default_cfg ( nvsram2_t *ctx );

Example key functions :

  • nvsram2_hold The function enables hold operation by setting the state of the HOLD ( PWM ) pin depending on the function argument.

    void nvsram2_hold ( nvsram2_t *ctx, uint8_t en_hold );
  • nvsram2_set_cmd The function sends desired command to the CY14B101Q2A memory on nvSRAM 2 Click board.

    void nvsram2_set_cmd ( nvsram2_t *ctx, uint8_t cmd );
  • nvsram2_read_id The function performs the device ID read of the CY14B101Q2A memory on nvSRAM 2 Click board.

    uint32_t nvsram2_read_id ( nvsram2_t *ctx );

Example Description

This is an example using nvSRAM 2 Click based on CY14B101Q which is combines a 1-Mbit nvSRAM with a nonvolatile element in each memory cell with serial SPI interface. The memory is organized as 128K words of 8 bits each.

The demo application is composed of two sections :

Application Init

Initializes SPI and UART LOG, sets CS and PWM pins as outputs. Disables hold, sets write enable latch, targets the memory address at 12345 ( 0x00003039 ) for burst write starting point and writes data which is also displayed on the log.


void application_init ( void ) {
    log_cfg_t log_cfg;               /**< Logger config object. */
    nvsram2_cfg_t nvsram2_cfg;       /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    Delay_ms ( 100 );
    log_info( &logger, " Application Init " );

    // Click initialization.

    nvsram2_cfg_setup( &nvsram2_cfg );
    NVSRAM2_MAP_MIKROBUS( nvsram2_cfg, MIKROBUS_1 );
    err_t init_flag  = nvsram2_init( &nvsram2, &nvsram2_cfg );
    if ( SPI_MASTER_ERROR == init_flag ) {

        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }

    nvsram2_default_cfg ( &nvsram2 );
    log_info( &logger, " Application Task " );

    memory_addr = 12345;

    nvsram2_burst_write( &nvsram2, memory_addr, demo_data, 9 );
    log_printf( &logger, "-----------------------\r\n" );
    log_printf( &logger, "-> Write data : %s \r\n", demo_data );
    Delay_ms ( 100 );
}

Application Task

This is an example that demonstrates the use of the nvSRAM 2 Click board. In this example, the data is read from the targeted memory address. The results are being sent to the Usart Terminal. This task repeats every 5 sec.


void application_task ( void ) {
    nvsram2_burst_read( &nvsram2, memory_addr, rx_data, 9 );
    log_printf( &logger, "-----------------------\r\n"  );
    log_printf( &logger, "<- Read data  : %s \r\n", rx_data );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}   

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.nvSRAM2

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

Analog MUX 3 Click

0

Analog MUX 3 Click is a compact add-on board that switches one of the eight inputs to one output. This board features the ADG738, a CMOS analog matrix switch with a serially-controlled SPI interface from Analog Devices. In an active state, the ADG738 conducts equally well in both directions, making it suitable for multiplexing and demultiplexing applications. It can also be configured as a type of switch array where any, all, or none of eight switches may be closed any time. All channels exhibit ‘break-before-make switching action, preventing momentary shorting when switching channels. This Click board™ is suitable for a wide range of applications, from industrial and instrumentation to medical, consumer, communications, and automotive systems.

[Learn More]

LED Driver 14 Click

0

LED Driver 14 Click is a compact add-on board that simplifies the control of multiple LEDs. This board features the BD18337EFV-M, a reliable four-channel constant current LED driver from Rohm Semiconductor. It is powered by an external power supply in the range of 5.5V to 20V, providing a maximum output current of 150mA per channel. The BD18337EFV-M also comes with the possibility for up to 3 LEDs in series on its output OUTx pin and built-in energy sharing control, selectable operational mode, and multiple built-in protection functions that protect the circuit during abnormalities. This Click board™ is ideal for LED rear lamps (turn/stop), fog lamps, and turn signals for automotive applications.

[Learn More]

Driver 2 click

5

Driver 2 Click is a compact add-on board that contains a gate driver with a level-shift technology with an additional Shutdown function.

[Learn More]