TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141481 times)
  2. FAT32 Library (74339 times)
  3. Network Ethernet Library (58869 times)
  4. USB Device Library (48921 times)
  5. Network WiFi Library (44698 times)
  6. FT800 Library (44229 times)
  7. GSM click (30938 times)
  8. mikroSDK (29817 times)
  9. PID Library (27423 times)
  10. microSD click (27375 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

Stepper 7 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.3

mikroSDK Library: 2.0.0.0

Category: Stepper

Downloaded: 80 times

Not followed.

License: MIT license  

Stepper 7 Click is a bipolar step motor driver. It features an H-bridge bipolar step motor driver, which supports full and half step control modes. Stepper 7 Click also carries a port expander so that the communication can be done with a minimal number of pins, through the mikroBUS™ SPI bus.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Stepper 7 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Stepper 7 Click" changes.

Do you want to report abuse regarding "Stepper 7 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


Stepper 7 Click

Stepper 7 Click is a bipolar step motor driver. It features an H-bridge bipolar step motor driver, which supports full and half step control modes. Stepper 7 Click also carries a port expander so that the communication can be done with a minimal number of pins, through the mikroBUS™ SPI bus.

stepper7_click.png

Click Product page


Click library

  • Author : Stefan Filipovic
  • Date : Feb 2024.
  • Type : SPI type

Software Support

We provide a library for the Stepper 7 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for Stepper 7 Click driver.

Standard key functions :

  • stepper7_cfg_setup Config Object Initialization function.

    void stepper7_cfg_setup ( stepper7_cfg_t *cfg );
  • stepper7_init Initialization function.

    err_t stepper7_init ( stepper7_t *ctx, stepper7_cfg_t *cfg );
  • stepper7_default_cfg Click Default Configuration function.

    err_t stepper7_default_cfg ( stepper7_t *ctx );

Example key functions :

  • stepper7_set_direction This function sets the motor direction to clockwise or counter-clockwise in ctx->direction.

    void stepper7_set_direction ( stepper7_t *ctx, uint8_t dir );
  • stepper7_set_step_mode This function sets the step mode resolution settings in ctx->step_mode.

    void stepper7_set_step_mode ( stepper7_t *ctx, uint8_t mode );
  • stepper7_drive_motor This function drives the motor for the specific number of steps at the selected speed.

    err_t stepper7_drive_motor ( stepper7_t *ctx, uint32_t steps, uint8_t speed );

Example Description

This example demonstrates the use of the Stepper 7 Click board by driving the motor in both directions for a desired number of steps.

The demo application is composed of two sections :

Application Init

Initializes the driver and performs the Click default configuration.


void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    stepper7_cfg_t stepper7_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    stepper7_cfg_setup( &stepper7_cfg );
    STEPPER7_MAP_MIKROBUS( stepper7_cfg, MIKROBUS_1 );
    if ( SPI_MASTER_ERROR == stepper7_init( &stepper7, &stepper7_cfg ) )
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }

    if ( STEPPER7_ERROR == stepper7_default_cfg ( &stepper7 ) )
    {
        log_error( &logger, " Default configuration." );
        for ( ; ; );
    }

    log_info( &logger, " Application Task " );
}

Application Task

Drives the motor clockwise for 200 full steps and then counter-clockiwse for 200 half steps and 800 1/8th steps with 2 seconds delay on driving mode change. All data is being logged on the USB UART where you can track the program flow.

void application_task ( void )
{
    log_printf ( &logger, " Move 200 full steps clockwise, speed: slow\r\n\n" );
    stepper7_set_direction ( &stepper7, STEPPER7_DIR_CW );
    stepper7_set_step_mode ( &stepper7, STEPPER7_MODE_FULL_STEP );
    stepper7_drive_motor ( &stepper7, 200, STEPPER7_SPEED_SLOW );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf ( &logger, " Move 200 half steps counter-clockwise, speed: medium\r\n\n" );
    stepper7_set_direction ( &stepper7, STEPPER7_DIR_CCW );
    stepper7_set_step_mode ( &stepper7, STEPPER7_MODE_HALF_STEP );
    stepper7_drive_motor ( &stepper7, 200, STEPPER7_SPEED_MEDIUM );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf ( &logger, " Move 800 1/8th steps counter-clockwise, speed: fast\r\n\n" );
    stepper7_set_direction ( &stepper7, STEPPER7_DIR_CCW );
    stepper7_set_step_mode ( &stepper7, STEPPER7_MODE_1_OVER_8_STEP );
    stepper7_drive_motor ( &stepper7, 800, STEPPER7_SPEED_FAST );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.Stepper7

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.


ALSO FROM THIS AUTHOR

LED Driver 2 Click

0

LED driver 2 Click carries the MCP1643 - LED constant current regulator, made by Microchip. It is a compact, high-efficiency, fixed frequency, synchronous step-up converter, optimized to drive one LED with the constant current.

[Learn More]

Air quality 9 Click

0

Air quality 9 Click is a compact add-on board containing a best-in-class air-quality sensing solution. This board features the ENS160, a digital multi-gas sensor solution based on metal oxide (MOX) technology with four MOx sensor elements from ScioSense. Each sensor element has independent hotplate control to detect a wide range of gases. The ENS160 series features TrueVOCâ„¢ air quality detection and supports intelligent algorithms, which calculate CO2 equivalents, TVOC, air quality index (AQI), and perform humidity and temperature compensation. This Click boardâ„¢ is interface-configurable and characterized by outstanding long-term stability and lifetime.

[Learn More]

ReRAM click

5

ReRAM Click features ReRAM (Resistive Random Access Memory) module which contains the cell array made of 524.288 words x 8 bits, which totals 4 Mbits of data.

[Learn More]