TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (404 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141135 times)
  2. FAT32 Library (73919 times)
  3. Network Ethernet Library (58555 times)
  4. USB Device Library (48747 times)
  5. Network WiFi Library (44409 times)
  6. FT800 Library (44003 times)
  7. GSM click (30722 times)
  8. mikroSDK (29479 times)
  9. PID Library (27308 times)
  10. microSD click (27135 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
Visual TFT/GLCD Project

Mikromedia 5 for Tiva - RF Communication Example

Rating:

5

Author: MIKROE

Last Updated: 2013-12-17

Package Version: 1.0.0.0

Category: Communication

Downloaded: 875 times

Not followed.

License: MIT license  

This is demonstration project how Mikromedia 5 for Tiva communicates over RF. Data is send over simple 'led protocol' (1 byte command). Development board for Stellaris with an add-on board nRF Click is used as a receiver device.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Mikromedia 5 for Tiva - RF Communication Example" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Mikromedia 5 for Tiva - RF Communication Example" changes.

Do you want to report abuse regarding "Mikromedia 5 for Tiva - RF Communication Example".

  • Information
  • Comments (0)

Visual TFT/GLCD Project Blog

Mikromedia 5 for Tiva

Mikromedia 5 for Tiva

Front and back image of Mikromedia 5 for Tiva

View full image

Example requirements:
- Development board - EasyMX PRO v7 for Stellaris ARM

- MCU card with LM3S9B95

- Add-on board: nRF T Click or nRF C Click (used with development system)

- Mikromedia 5 for Tiva

ALSO FROM THIS AUTHOR

7x10 G Click

0

7x10 G Click is a LED dot matrix display Click, which can be used to display graphics or letters in a very simple and easy way. The Click board has two LED dot matrix modules with 7x5 stylish, round, dot-like LED elements. These displays produce clean and uniform patterns since the elements are optically isolated from each other and there is no light bleeding between the adjacent LED cells. Additionally, turn-on and turn-off times of the matrix cells are optimized for a clean and fluid display performance, with no flickering or lag.

[Learn More]

16x12 G Click

0

16x12 G Click carries a 16x12 LED display and the IS31FL3733 matrix driver. The Click is designed to run on either 3.3V or 5V power supply.

[Learn More]

MCP251863 Click

0

MCP251863 Click is a compact add-on board representing a complete CAN solution used as a control node in a CAN network. This board features the MCP251863, IC representing a compact solution with a controller and a transceiver in one package, the MCP2518FD and ATA6563 from Microchip. The ATA6563, a low-level physical layer IC (PHY), provides a physical connection with the CAN bus itself, while the CAN controller MCP2518FD represents an interface between the MCU and the PHY. It features three operating modes with dedicated fail-safe features, remote wake-up via CAN, and ideally passive behavior when powered off on the CAN bus. This Click board™ is suitable for developing a wide range of automotive diagnostic applications, even on MCUs that don’t support CAN interface.

[Learn More]