We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: Current sensor
Downloaded: 362 times
Not followed.
License: MIT license
Download [418.81KB]The Hall Current 4 Click is designed to measure relatively high current by using the integrated ACS70331 sensor.
[learn more]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.12
mikroSDK Library: 2.0.0.0
Category: Temperature & humidity
Downloaded: 223 times
Not followed.
License: MIT license
Download [348.77KB]IrThermo 2 Click is a non-contact temperature measurement solution. The Click board carries the TMP007 infrared thermopile sensor with an integrated math engine.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.23
mikroSDK Library: 2.0.0.0
Category: Amplifier
Downloaded: 315 times
Not followed.
License: MIT license
Download [619.92KB]2x20W Amp Click carries the MAX9744 stereo class D audio power amplifier from Maxim Integrated. This Click brings the Class AB sound performance with Class D efficiency.
[learn more] Author: MIKROE
Last Updated: 2019-01-11
Package Version: 1.0.0.1
mikroSDK Library: 1.0.0.0
Category: Amplifier
Downloaded: 5920 times
Not followed.
License: MIT license
Download [2.66MB]2x5W AMP click functions as an amplifier and features the TDA7491LP 2x5-watt dual BTL class-D audio amplifier. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over the following pins on the mikroBUSâ„¢ line: AN, RST, CS, PWM, INT.
[learn more] 
Author: dnaci
Last Updated: 2019-01-10
Package Version: 1.0.0.0
Category: USB
Downloaded: 593 times
Not followed.
License: MIT license
Download [402.19KB]This project is the bootloader library for the pic18f25k50 processor. Prepared with microC.
You can use it with the mikroe bootloader program.
I thank Mikroelektronika for the sample code.
NOTE: I think it is available in pic18LF25k50. But I didn't test it.
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.17
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 276 times
Not followed.
License: MIT license
Download [404.03KB]Current 2 Click is an accurate current sensing Click board™ suitable for a very accurate measurement of the current through the load.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.21
mikroSDK Library: 2.0.0.0
Category: Temperature & humidity
Downloaded: 514 times
Not followed.
License: MIT license
Download [401.67KB]It’s a low cost reliable solution that communicates with the target board microcontroller through a single Serial Data Line.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.20
mikroSDK Library: 2.0.0.0
Category: Boost
Downloaded: 382 times
Not followed.
License: MIT license
Download [457.69KB]Boost 4 Click carries the TPS61230A, a high efficiency fully integrated synchronous boost converter from Texas Instruments. The Click is designed to run on a 3.3V power supply.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.16
mikroSDK Library: 2.0.0.0
Category: Optical
Downloaded: 372 times
Not followed.
License: MIT license
Download [372.65KB]UV 2 Click is a mikroBUS™ add-on board with a VEML6075 UVA and UVB light sensor. VEML6075 is a CMOS chip that incorporates a photodiode, amplifiers,and analog/digital circuits.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: Temperature & humidity
Downloaded: 365 times
Not followed.
License: MIT license
Download [446.32KB]DHT22 2 Click is used for measuring the environmental temperature and relative humidity. It uses the AM2322 sensor, with very accurate thermal and humidity measuring capabilities. It can use either 1-Wire or I2C protocol to communicate with the integrated circuit.
[learn more] 
