We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 139 times
Not followed.
License: MIT license
Download [508.57KB]Current 3 Click is a compact add-on board for applications like current sense and temperature monitoring.
[learn more]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.16
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 243 times
Not followed.
License: MIT license
Download [572.83KB]Analog MUX 3 Click is a compact add-on board that switches one of the eight inputs to one output. This board features the ADG738, a CMOS analog matrix switch with a serially-controlled SPI interface from Analog Devices. In an active state, the ADG738 conducts equally well in both directions, making it suitable for multiplexing and demultiplexing applications. It can also be configured as a type of switch array where any, all, or none of eight switches may be closed any time. All channels exhibit ‘break-before-make switching action, preventing momentary shorting when switching channels. This Click board™ is suitable for a wide range of applications, from industrial and instrumentation to medical, consumer, communications, and automotive systems.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.12
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 167 times
Not followed.
License: MIT license
Download [586.02KB]HZ to V Click is a device that can converts input frequency of the signal with virtually any wave shape to a DC voltage output, with a level proportional to the input frequency. It has a linear response, and by applying a signal with the frequency between 1kHz to 10kHz on its input, the Click board™ will generate a DC voltage, ranging from 0.33V to 3.3V.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.17
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 233 times
Not followed.
License: MIT license
Download [646.20KB]VCP Monitor 2 Click is a three-channel, high-side current and bus voltage monitor with alert indication function ensuring the intended application works within desired operating conditions. Featured chip INA3221-Q1, by Texas Instruments, monitors both shunt voltage drops and bus supply voltages, in addition to having programmable conversion times and averaging modes for these signals.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.12
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 182 times
Not followed.
License: MIT license
Download [647.27KB]PWR Meter Click is a power measurement Click board™, capable of measuring voltage and current through the load, connected to either AC or DC power source. PWR Meter Click uses the MCP39F511A, a very sophisticated monitoring IC from Microchip, with 16-bit processing core.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.21
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 210 times
Not followed.
License: MIT license
Download [574.09KB]Analog MUX 2 Click is a compact add-on board that switches one of the eight inputs to one output. This board features the ADG728, a low voltage, CMOS 8-channel analog matrix switch with a serially controlled 2-wire interface from Analog Devices. The ADG728 can operate equally well as either multiplexer, demultiplexer, or switch array easily connected to a 9 pole spring action block terminal. It provides flexibility and features a low on-resistance closely matched between switches and very flat over the full signal range. This Click board™ is suitable for a wide range of applications, from industrial and instrumentation to medical, consumer, communications, and automotive systems.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.12
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 206 times
Not followed.
License: MIT license
Download [582.87KB]V to Hz 2 Click is a device that converts an analog voltage input signal into a pulse wave signal of a certain frequency.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.14
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 222 times
Not followed.
License: MIT license
Download [526.80KB]PAC1934 Click carries the PAC1934 four channel DC power/energy monitor from Microchip. The Click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over an I2C interface.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.15
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 217 times
Not followed.
License: MIT license
Download [463.12KB]LEM Click carries the LTS 6-NP current transducer and MCP3201 ADC converter. The Click can measure AC and DC current with exceptional speed, up to 200 KHz.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.17
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 212 times
Not followed.
License: MIT license
Download [573.82KB]HZ to V 2 Click is a device that can convert input frequency of the signal with virtually any wave shape to a DC voltage output, with a level proportional to the input frequency.
[learn more] 
