TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141481 times)
  2. FAT32 Library (74339 times)
  3. Network Ethernet Library (58869 times)
  4. USB Device Library (48921 times)
  5. Network WiFi Library (44698 times)
  6. FT800 Library (44229 times)
  7. GSM click (30938 times)
  8. mikroSDK (29817 times)
  9. PID Library (27423 times)
  10. microSD click (27375 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

Fan 2 click

Rating:

6

Author: MIKROE

Last Updated: 2019-05-03

Package Version: 1.0.0.1

mikroSDK Library: 1.0.0.0

Category: Brushless

Downloaded: 6241 times

Not followed.

License: MIT license  

Fan 2 click carries the MAX31760 precision fan-speed controller. It can also measure temperature and adjust the fan speed to keep the temperature at the same level.

The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Fan 2 click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Fan 2 click" changes.

Do you want to report abuse regarding "Fan 2 click".

  • mikroSDK Library 2.0.0.0
  • Comments (0)
DOWNLOAD LINK RELATED COMPILER CONTAINS
mikroBasic PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroBasic PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroC PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for ARM
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for AVR
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for dsPIC30/33 & PIC24
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for FT90x
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for PIC
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc
mikroPascal PRO for PIC32
  • lib
  • src
  • exa
  • hlp
  • hex
  • sch
  • pcb
  • doc

mikroSDK Library Blog

Fan 2 click

Fan 2 click

Native view of the Fan 2 click board.

View full image
Fan 2 click

Fan 2 click

Front and back view of the Fan 2 click board.

View full image

Library Description

The library initializes and defines the I2C bus driver and drivers that offer a choice for writing and reading
one byte or two bytes of data in and from registers. The library includes a functions for reading temperature from internal or external sensor,reading and writing from control registers, fan fault duty cycle register, alert mask register, ideality factor Register, remote\local high set-point register,remote\local overtemperature set-point register, TACH count threshold registers, lookup table registers, direct duty-cycle control register and EEPROM LOAD/WRITE register.Current PWM duty-cycle register TACH1 count register, TACH2 Count register and status register can only be read. User can also use functions to check the state of the ALR SHD FF INT pins.

Key functions:

  • void fan2_writeCtrl1( uint8_t wrData ) - Function writes 8-bit data into control register 1.
  • float fan2_readLocalTempReg() - Function is used to read temperature from an internal measuring device.
  • void fan2_writeLookupTable( uint8_t lutVal ) - Function is used to write into Lookup Table registers.

Examples description

The application is composed of the three sections :

  • System Initialization - Initializes I2C module, LOG and GPIO structures, sets AN, RST, CS and INT pins as input.
  • Application Initialization - Initalizes I2C driver, applies manual control settings and makes an initial log.
  • Application Task - (code snippet) This example demonstrates the use of Fan 2 Click board. It measures current temperature, using an internal sensor and logs values. In case of temerature exceeding 30 degree centigrade it rans a fan.
void applicationTask( )
{
    temperature = fan2_readLocalTempReg();

    FloatToStr( temperature, logTxt );
    mikrobus_logWrite( "Temperature : ", _LOG_TEXT );
    mikrobus_logWrite( logTxt, _LOG_TEXT );
    mikrobus_logWrite( degCel, _LOG_LINE );
    if( temperature > 30 )
    {
        fan2_writeDirDutCycCtrlReg( _FAN2_DUTYCYCLE_100 );
    }
    else
    {
        fan2_writeDirDutCycCtrlReg( _FAN2_DUTYCYCLE_0 );
    }
    Delay_ms( 1000 );
}

Other mikroE Libraries used in the example:

  • I2C
  • UART
  • Conversions

Additional notes and informations

Depending on the development board you are using, you may need USB UART clickUSB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

ALSO FROM THIS AUTHOR

RTC 10 Click

0

RTC 10 Click is a real-time clock module which has an extremely low power consumption, allowing it to be used with a single button cell battery, for an extended period of time.

[Learn More]

IPD 2 Click

0

IPD 2 Click is a compact add-on board for efficient and reliable high-side switching in automotive applications. This board features the BV2HD070EFU-C, an automotive-grade two-channel high-side switch from ROHM Semiconductor with advanced protection and diagnostic functionalities. This 70mΩ on-resistance high-side switch supports an input voltage range from 6V to 28V and includes built-in protection mechanisms such as overcurrent detection, thermal shutdown, undervoltage lockout, and open load detection. Additionally, it offers configurable overcurrent limits and diagnostic output for real-time fault feedback, ensuring enhanced system reliability.

[Learn More]

Thumbstick click

5

The joystick unit receives directional input in the x and y axes by way of two potentiometers connected to a stick. The mechanical pushbutton sends an interrupt signal to the microcontroller. TFT shows values.

[Learn More]