We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Rating:
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.26
mikroSDK Library: 2.0.0.0
Category: Magnetic
Downloaded: 300 times
Not followed.
License: MIT license
3D Hall 6 Click is a very accurate, magnetic field sensing Click board™, used to measure the intensity of the magnetic field across three perpendicular axes.
Do you want to subscribe in order to receive notifications regarding "3D Hall 6 Click" changes.
Do you want to unsubscribe in order to stop receiving notifications regarding "3D Hall 6 Click" changes.
Do you want to report abuse regarding "3D Hall 6 Click".
DOWNLOAD LINK | RELATED COMPILER | CONTAINS |
---|---|---|
3286_3d_hall_6_click.zip [562.96KB] | mikroC AI for ARM GCC for ARM Clang for ARM mikroC AI for PIC mikroC AI for PIC32 XC32 GCC for RISC-V Clang for RISC-V mikroC AI for AVR mikroC AI for dsPIC XC16 |
|
3D Hall 6 Click is a very accurate, magnetic field sensing Click board™, used to measure the intensity of the magnetic field across three perpendicular axes.
We provide a library for the 3dHall6 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.
This library contains API for 3dHall6 Click driver.
c3dhall6_cfg_setup
Config Object Initialization function.
void c3dhall6_cfg_setup ( c3dhall6_cfg_t *cfg );
c3dhall6_init
Initialization function.
err_t c3dhall6_init ( c3dhall6_t *ctx, c3dhall6_cfg_t *cfg );
c3dhall6_set_reference_values
This function sets reference values for voltage and angle calculations.
void c3dhall6_set_reference_values ( c3dhall6_t *ctx, c3dhall6_aux_ref_t ref_val );
c3dhall6_get_adc_value
This function reads ADC value on selected channel.
void c3dhall6_get_adc_value ( c3dhall6_t *ctx, uint8_t channel_no, uint16_t *adc_value );
c3dhall6_get_volt
This function reads ADC value on selected channel and converts that value to Volts or miliVolts - depending on reference voltage setting.
void c3dhall6_get_volt( c3dhall6_t *ctx, uint8_t channel_no, float *channel_voltage );
This application measure the intensity of the magnetic field across three perpendicular axes.
The demo application is composed of two sections :
Initializes device.
void application_init ( void )
{
log_cfg_t log_cfg;
c3dhall6_cfg_t cfg;
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
c3dhall6_cfg_setup( &cfg );
C3DHALL6_MAP_MIKROBUS( cfg, MIKROBUS_1 );
c3dhall6_init( &c3dhall6, &cfg );
c3dhall6_aux_ref_t ref_val =
{
.aux_ref_adc_ch0 = 2048.0,
.aux_ref_adc_ch1 = 2048.0,
.aux_ref_adc_ch2 = 2048.0,
.aux_ref_adc_ch3 = 2048.0,
.aux_ref_volt = 3.3
};
c3dhall6_set_reference_values( &c3dhall6, ref_val );
log_info( &logger, " Application Task " );
}
Executes one or more 'c3dhall6_log_xxx_task' functions Additional Functions :
- c3dhall6_log_adc_task() - performs and logs adc measurements on all channels
- c3dhall6_log_volt_task() - performs and logs voltage measurements on all channels
- c3dhall6_log_angleRad_task() - performs and logs angle measurements in radians on each die
- c3dhall6_log_angleDeg_task() - performs and logs angle measurements in degrees on each die
void application_task ( void )
{
c3dhall6_log_angle_deg_task( );
Delay_ms ( 1000 );
}
The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.
Other mikroE Libraries used in the example:
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.