We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Rating:
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.17
mikroSDK Library: 2.0.0.0
Category: RTC
Downloaded: 259 times
Not followed.
License: MIT license
This application give time and date information
Do you want to subscribe in order to receive notifications regarding "RTC 2 Click" changes.
Do you want to unsubscribe in order to stop receiving notifications regarding "RTC 2 Click" changes.
Do you want to report abuse regarding "RTC 2 Click".
DOWNLOAD LINK | RELATED COMPILER | CONTAINS |
---|---|---|
3471_rtc_2_click.zip [528.29KB] | mikroC AI for ARM GCC for ARM Clang for ARM mikroC AI for PIC mikroC AI for PIC32 XC32 GCC for RISC-V Clang for RISC-V mikroC AI for AVR mikroC AI for dsPIC XC16 |
|
< RTC2 Click is an accessory board in mikroBus™ form factor. It features the DS1307 serial real-time clock (RTC). It is a low-power, full binary-coded decimal (BCD) clock/calendar with programmable square-wave output signal. >
We provide a library for the Rtc2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.
This library contains API for Rtc2 Click driver.
Config Object Initialization function.
void rtc2_cfg_setup ( rtc2_cfg_t *cfg );
Initialization function.
RTC2_RETVAL rtc2_init ( rtc2_t ctx, rtc2_cfg_t cfg );
Generic read byte of data function.
uint8_t rtc2_read_byte ( rtc2_t *ctx, uint8_t reg_address );
Generic write byte of data function.
void rtc2_write_byte ( rtc2_t *ctx, uint8_t reg_address, uint8_t write_data );
Enable counting function.
void rtc2_enable_counting ( rtc2_t *ctx );
This application give time and day information.
The demo application is composed of two sections :
Initialization driver enable's - I2C,set start time and date, enable counting and start write log.
void application_init ( void )
{
log_cfg_t log_cfg;
rtc2_cfg_t cfg;
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, "---- Application Init ----" );
// Click initialization.
rtc2_cfg_setup( &cfg );
RTC2_MAP_MIKROBUS( cfg, MIKROBUS_1 );
rtc2_init( &rtc2, &cfg );
rtc2_set_time( &rtc2, 23, 59, 50 );
rtc2_set_date( &rtc2, 1, 31, 12, 2018 );
rtc2_enable_counting( &rtc2 );
}
This is a example which demonstrates the use of RTC 2 Click board. RTC 2 Click communicates with register via I2C by write to register and read from register, set time and date, get time and date, enable and disable counting and set frequency by write configuration register. Results are being sent to the Usart Terminal where you can track their changes. All data logs write on usb uart changes for every 1 sec.
void application_task ( void )
{
rtc2_get_time( &rtc2, &time_hours, &time_minutes, &time_seconds );
rtc2_get_date( &rtc2, &day_of_the_week, &date_day, &date_month, &date_year );
if ( time_seconds_new != time_seconds )
{
log_printf( &logger, " Time : " );
display_log_uart( time_hours );
log_printf( &logger, ":" );
display_log_uart( time_minutes );
log_printf( &logger, ":" );
display_log_uart( time_seconds );
log_printf( &logger, "" );
display_day_of_the_week( day_of_the_week );
log_printf( &logger, " Date: " );
display_log_uart( date_day );
log_printf( &logger, "." );
display_log_uart( date_month );
log_printf( &logger, "." );
log_printf( &logger, "20" );
display_log_uart( date_year );
log_printf( &logger, "." );
log_printf( &logger, "-------------------" );
time_seconds_new = time_seconds;
}
}
Additional Functions :
The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.
Other mikroE Libraries used in the example:
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.