We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Rating:
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.17
mikroSDK Library: 2.0.0.0
Category: Optical
Downloaded: 221 times
Not followed.
License: MIT license
Smoke Click carries the MAX30105 high-sensitivity optical sensor for smoke detection. The Click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over I2C interface with additional functionality provided by the INT pin on the mikroBUS™ line.
Do you want to subscribe in order to receive notifications regarding "Smoke Click" changes.
Do you want to unsubscribe in order to stop receiving notifications regarding "Smoke Click" changes.
Do you want to report abuse regarding "Smoke Click".
DOWNLOAD LINK | RELATED COMPILER | CONTAINS |
---|---|---|
3674_smoke_click.zip [463.95KB] | mikroC AI for ARM GCC for ARM Clang for ARM mikroC AI for PIC mikroC AI for PIC32 XC32 GCC for RISC-V Clang for RISC-V mikroC AI for AVR mikroC AI for dsPIC XC16 |
|
Smoke Click carries the MAX30105 high-sensitivity optical sensor for smoke detection. The Click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over I2C interface with additional functionality provided by the INT pin on the mikroBUS™ line.
We provide a library for the Smoke Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.
This library contains API for Smoke Click driver.
Config Object Initialization function.
void smoke_cfg_setup ( smoke_cfg_t *cfg );
Initialization function.
SMOKE_RETVAL smoke_init ( smoke_t ctx, smoke_cfg_t cfg );
Click Default Configuration function.
void smoke_default_cfg ( smoke_t *ctx );
Set registers values function.
uint8_t smoke_set_registers ( smoke_t ctx, smoke_set_registers_t registers );
Enable or disable interrupt function.
uint8_t smoke_enable_disable_interrupts ( smoke_t *ctx, uint8_t interrupt_flag, uint8_t enable_flag );
Function for reading enabled led values.
uint8_t smoke_read_leds ( smoke_t *ctx );
This Click includes internal LEDs, photodetectors, optical elements, and low-noise electronics with ambient light rejection. The sensor can detect a wide variety of smoke particle sizes. It also has an on-chip temperature sensor for calibrating the temperature dependence of the particle sensing subsystem. The temperature sensor has an inherent resolution 0.0625°C.
The demo application is composed of two sections :
Initalizes I2C driver, and sets default configuration of device.
void application_init ( void )
{
log_cfg_t log_cfg;
smoke_cfg_t cfg;
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, "---- Application Init ----" );
// Click initialization.
smoke_cfg_setup( &cfg );
SMOKE_MAP_MIKROBUS( cfg, MIKROBUS_1 );
smoke_init( &smoke, &cfg );
smoke_reset( &smoke );
smoke_default_cfg ( &smoke );
log_info( &logger, "---- Application Task ----" );
Delay_ms ( 100 );
if ( smoke_read_leds( &smoke ) != SMOKE_OK )
{
log_info( &logger, "---- Init Error ----" );
for( ; ; );
}
}
This example demonstrates the use of Smoke Click board. It reads reflected red, ir, green and temperature values from an internal sensor and displays and logs it.
void application_task ( void )
{
smoke_read_leds( &smoke );
log_printf( &logger, "Red : %llu\r\n", smoke.red_value );
log_printf( &logger, "IR : %llu\r\n", smoke.ir_value );
log_printf( &logger, "Green : %llu\r\n", smoke.green_value );
log_printf( &logger, "------------------------------\r\n" );
temperature = smoke_read_temp( &smoke );
log_printf( &logger, "Read Temperature[ degC ]: %.2f\r\n", temperature );
log_printf( &logger, "------------------------------\r\n" );
Delay_ms ( 500 );
}
The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.
Other mikroE Libraries used in the example:
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.