TOP Contributors

  1. MIKROE (2762 codes)
  2. Alcides Ramos (374 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (118 codes)
  5. Bugz Bensce (90 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (139255 times)
  2. FAT32 Library (71751 times)
  3. Network Ethernet Library (57122 times)
  4. USB Device Library (47430 times)
  5. Network WiFi Library (43082 times)
  6. FT800 Library (42404 times)
  7. GSM click (29835 times)
  8. mikroSDK (28078 times)
  9. PID Library (26885 times)
  10. microSD click (26198 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

I2C isolator Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.12

mikroSDK Library: 2.0.0.0

Category: I2C

Downloaded: 155 times

Not followed.

License: MIT license  

I2C Isolator Click carries ISO1540, a low-power, bidirectional isolator compatible with I2C interfaces. On the board, the Texas Instruments chip is connected to two sets of I2C pins, one on the mikroBUS connector (SDA, SCL), the other on the upper edge of the board (SCL2, SDL2).

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "I2C isolator Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "I2C isolator Click" changes.

Do you want to report abuse regarding "I2C isolator Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


I2C isolator Click

I2C Isolator Click carries ISO1540, a low-power, bidirectional isolator compatible with I2C interfaces. On the board, the Texas Instruments chip is connected to two sets of I2C pins, one on the mikroBUS connector (SDA, SCL), the other on the upper edge of the board (SCL2, SDL2).

i2cisolator_click.png

Click Product page


Click library

  • Author : MikroE Team
  • Date : Jan 2020.
  • Type : I2C type

Software Support

We provide a library for the I2Cisolator Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for I2Cisolator Click driver.

Standard key functions :

  • Config Object Initialization function.

    void i2cisolator_cfg_setup ( i2cisolator_cfg_t *cfg );

  • Initialization function.

    I2CISOLATOR_RETVAL i2cisolator_init ( i2cisolator_t ctx, i2cisolator_cfg_t cfg );

Example key functions :

  • Generic write function.

    void i2cisolator_generic_write ( i2cisolator_t ctx, uint8_t reg, uint8_t data_buf, uint8_t len );

  • Generic read function.

    void i2cisolator_generic_read ( i2cisolator_t ctx, uint8_t reg, uint8_t data_buf, uint8_t len );

Examples Description

This is an example which demonstrates the use of I2C Isolator Click board.

The demo application is composed of two sections :

Application Init

Initialization driver enables - I2C, sets configuration of TMP007 sensor on IrThermo 2 Click and start to write log.


void application_init ( void )
{
    log_cfg_t log_cfg;
    i2cisolator_cfg_t cfg;
    uint8_t tmp;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    i2cisolator_cfg_setup( &cfg );
    I2CISOLATOR_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    i2cisolator_init( &i2cisolator, &cfg );

    log_printf( &logger, "    Driver  Initialized\r\n" );
    log_printf( &logger, "---------------------------\r\n" );
    Delay_ms ( 100 );

    tmp =    I2CISOLATOR_IRTHERMO2_CFG_MODEON |
                I2CISOLATOR_IRTHERMO2_CFG_ALERTEN | 
                I2CISOLATOR_IRTHERMO2_CFG_TRANSC | 
                I2CISOLATOR_IRTHERMO2_CFG_16SAMPLE;
    i2cisolator_generic_write( &i2cisolator, I2CISOLATOR_IRTHERMO2_CONFIGURATION, &tmp, 1 );

    tmp =    I2CISOLATOR_IRTHERMO2_STAT_ALERTEN | 
                I2CISOLATOR_IRTHERMO2_STAT_CRTEN;
    i2cisolator_generic_write( &i2cisolator, I2CISOLATOR_IRTHERMO2_STATUS_MASK_AND_ENABLE, &tmp, 1 );    

    log_printf( &logger, "       Configuration\r\n" );
    log_printf( &logger, "      IrThermo 2 Click\r\n" );
    log_printf( &logger, "---------------------------\r\n" );
    Delay_ms ( 100 );
}

Application Task

In this example we use IrThermo 2 Click, measures the temperature with, and calculate the temperature in degrees Celsius [ C ]. Results are being sent to the USART Terminal where you can track their changes. All data logs on usb uart each second.


void application_task ( void )
{
    i2cisolator_get_temperature( );   

    log_printf( &logger, " Temperature : %0.2f C\r\n", temperature );
    log_printf( &logger, "---------------------------\r\n" );
    Delay_ms ( 1000 );
} 

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.I2Cisolator

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

Current click

0

This project is a simple demonstration of working with the <b>Current Click</b> board based on the MCP3201 12-bit Analog-to-Digital Converter (ADC) with SPI Interface. This example demosntrates measuring the current drawn by the consumer using a shunt resistor.

[Learn More]

AlphaNum G Click

0

AlphaNum Click is a simple solution for adding 14-segment alphanumeric display to your device. The board carries two TLC5926 16-bit Constant-Current LED sink Drivers

[Learn More]

M-BUS Master click

5

The M-Bus Master is a Click board is complete solution for a master node in M-Bus networks. The M-Bus (&amp;quot;Meter-Bus&amp;quot;) is a new European standard for remote reading of heat meters and it is also usable for all other types of consumption meters as well as for various sensors and actuators.

[Learn More]