TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141697 times)
  2. FAT32 Library (74777 times)
  3. Network Ethernet Library (59218 times)
  4. USB Device Library (49226 times)
  5. Network WiFi Library (44999 times)
  6. FT800 Library (44536 times)
  7. GSM click (31200 times)
  8. mikroSDK (30103 times)
  9. microSD click (27586 times)
  10. PID Library (27540 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

DC Motor 9 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.16

mikroSDK Library: 2.0.0.0

Category: Brushed

Downloaded: 409 times

Not followed.

License: MIT license  

DC Motor 9 Click is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8871, an integrated H-Bridge driver IC, optimized for motor driving applications. It can be operated by two logic signals, allowing to drive the connected motor in two different ways: it can use fixed logic levels for the direction control, or it can be controlled by a PWM signal, offering an additional speed control option. The DRV8871 also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 9 Click can also sense current consumption at its output.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "DC Motor 9 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "DC Motor 9 Click" changes.

Do you want to report abuse regarding "DC Motor 9 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


DC Motor 9 Click

DC Motor 9 Click is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8871, an integrated H-Bridge driver IC, optimized for motor driving applications. It can be operated by two logic signals, allowing to drive the connected motor in two different ways: it can use fixed logic levels for the direction control, or it can be controlled by a PWM signal, offering an additional speed control option. The DRV8871 also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 9 Click can also sense current consumption at its output.

dcmotor9_click.png

Click Product page


Click library

  • Author : Nikola Peric
  • Date : Feb 2022.
  • Type : PWM type

Software Support

We provide a library for the DcMotor9 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for DcMotor9 Click driver.

Standard key functions :

  • Config Object Initialization function.

    void dcmotor9_cfg_setup ( dcmotor9_cfg_t *cfg );

  • Initialization function.

    DCMOTOR9_RETVAL dcmotor9_init ( dcmotor9_t ctx, dcmotor9_cfg_t cfg );

Example key functions :

  • This function read ADC data.

    dcmotor9_data_t dcmotor9_generic_read ( dcmotor9_t *ctx );

  • This function starts PWM module.

    void dcmotor9_pwm_start ( dcmotor9_t *ctx );

  • This function sets the PWM duty cycle.

    void dcmotor9_set_duty_cycle ( dcmotor9_t *ctx, float duty_cycle );

Examples Description

DC Motor 9 Click is a brushed DC motor driver with the current limiting and current sensing. It can be operated by two logic signals, allowing to drive the connected motor in two different ways: it can use fixed logic levels for the direction control, or it can be controlled by a PWM signal, offering an additional speed control option.

The demo application is composed of two sections :

Application Init

Initializes GPIO, PWM and logger and enables the Click board.


void application_init ( void )
{
    log_cfg_t log_cfg;
    dcmotor9_cfg_t dcmotor9_cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    dcmotor9_cfg_setup( &dcmotor9_cfg );
    DCMOTOR9_MAP_MIKROBUS( dcmotor9_cfg, MIKROBUS_1 );
    if ( dcmotor9_init( &dcmotor9, &dcmotor9_cfg ) == PWM_ERROR )
    {
        log_info( &logger, "---- Application Init Error ----" );
        log_info( &logger, "---- Please, run program again ----" );

        for ( ; ; );
    }

    dcmotor9_set_duty_cycle ( &dcmotor9, DCMOTOR9_PWM_DUTY_PERCENT_0 );

    dcmotor9_enable( &dcmotor9 );
    dcmotor9_pwm_start( &dcmotor9 );
    log_info( &logger, "---- Application Task ----" );
    Delay_ms ( 1000 );
}

Application Task

This is a example which demonstrates the use of DC Motor 5 Click board. DC Motor 9 Click controls DC Motor speed via PWM interface. It shows moving in the both directions from slow to fast speed and from fast to slow speed. Results are being sent to the Usart Terminal where you can track their changes.

void application_task ( void ) { static float duty; static uint8_t n_cnt;

dcmotor9_clockwise ( &dcmotor9 );
log_printf( &logger, "> CLOCKWISE <\r\n" );
dcmotor9_enable ( &dcmotor9 );

for ( n_cnt = 10; n_cnt > 0; n_cnt--  )
{
    duty = ( float ) n_cnt ;
    duty /= 10;
    dcmotor9_set_duty_cycle( &dcmotor9, duty );
    Delay_ms ( 500 );
}
for ( n_cnt = 1; n_cnt <= 10; n_cnt++ )
{
    duty = ( float ) n_cnt ;
    duty /= 10;
    dcmotor9_set_duty_cycle( &dcmotor9,  duty );
    Delay_ms ( 500 );
}

log_printf( &logger, "* Pull break *\r\n" );
dcmotor9_short_brake( &dcmotor9 );
Delay_ms ( 1000 );

dcmotor9_counter_clockwise ( &dcmotor9 );
log_printf( &logger, "> COUNTER CLOCKWISE <\r\n" );

for ( n_cnt = 1; n_cnt <= 10; n_cnt++  )
{
    duty = ( float ) n_cnt ;
    duty /= 10;
    dcmotor9_set_duty_cycle( &dcmotor9, duty );
    Delay_ms ( 500 );
}
for ( n_cnt = 10; n_cnt > 0; n_cnt-- )
{
    duty = ( float ) n_cnt ;
    duty /= 10;
    dcmotor9_set_duty_cycle( &dcmotor9,  duty );
    Delay_ms ( 500 );
}

}



The full application code, and ready to use projects can be  installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

**Other mikroE Libraries used in the example:** 

- MikroSDK.Board
- MikroSDK.Log
- Click.DcMotor9

**Additional notes and informations**

Depending on the development board you are using, you may need 
[USB UART Click](https://shop.mikroe.com/usb-uart-click), 
[USB UART 2 Click](https://shop.mikroe.com/usb-uart-2-click) or 
[RS232 Click](https://shop.mikroe.com/rs232-click) to connect to your PC, for 
development systems with no UART to USB interface available on the board. The 
terminal available in all Mikroelektronika 
[compilers](https://shop.mikroe.com/compilers), or any other terminal application 
of your choice, can be used to read the message.



---

ALSO FROM THIS AUTHOR

Accel 31 Click

0

Accel 31 Click is a compact add-on board designed for precise motion and orientation detection in space-constrained devices. This board features the BMA580, a triaxial low-g accelerometer from Bosch Sensortec, which offers a 16-bit digital resolution with measurement ranges of ±2, ±4, ±8, and ±16 g, along with flexible output data rates from 1.56Hz to 6.4kHz, enabling high adaptability and accuracy. The BMA580 supports advanced power modes, including high-performance and low-power, self-wake-up functionality, and bone conduction-based voice activity detection.

[Learn More]

Step Down 12 Click

0

Step Down 12 Click is a compact add-on board for reliable DC-DC step-down applications. Based on Texas Instruments' TPS62902 synchronous step-down converter, it features the DCS-Control topology, which combines hysteretic, voltage mode, and current mode control for precision and fast response to voltage changes. Supporting a wide input voltage range of 3V to 17V, it provides stable output voltages with accuracy within ±1% and can enter power save mode for high efficiency under light loads. With 16 configurable output voltages from 0.7V to 5.5V, this Click board™ is ideal for applications in factory automation, building systems, data centers, enterprise computing, and motor drives where efficient, stable power conversion is essential.

[Learn More]

Accel 19 Click

0

Accel 19 Click is a compact add-on board that contains an acceleration sensor. This board features the LIS2DTW12, an ultra-low-power high-performance three-axis accelerometer from STMicroelectronics. It allows selectable full-scale acceleration measurements in ranges of ±2g, ±4g, ±8g, or ±16g in three axes with a configurable host interface that supports both SPI and I2C serial communication. Alongside an embedded 0.8°C accuracy temperature sensor with ODRs ranging from 50 to 1.6Hz and resolution from 8 to 12 bits, it has a dedicated internal engine to process motion and acceleration detection.

[Learn More]