TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141262 times)
  2. FAT32 Library (74085 times)
  3. Network Ethernet Library (58713 times)
  4. USB Device Library (48820 times)
  5. Network WiFi Library (44525 times)
  6. FT800 Library (44072 times)
  7. GSM click (30803 times)
  8. mikroSDK (29650 times)
  9. PID Library (27355 times)
  10. microSD click (27251 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

Audio Xover Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.15

mikroSDK Library: 2.0.0.0

Category: Signal processing

Downloaded: 315 times

Not followed.

License: MIT license  

Audio Xover Click is an analog active crossover solution for two-way loudspeakers. The primary purpose of the crossover circuit in a loudspeaker is to split an incoming audio signal into frequency bands that are passed to the speaker or “driver” best suited.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Audio Xover Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Audio Xover Click" changes.

Do you want to report abuse regarding "Audio Xover Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


Audio Xover Click

Audio Xover Click is an analog active crossover solution for two-way loudspeakers. The primary purpose of the crossover circuit in a loudspeaker is to split an incoming audio signal into frequency bands that are passed to the speaker or “driver” best suited.

audio_xover_click.png

Click Product page


Click library

  • Author : MikroE Team
  • Date : Jun 2020.
  • Type : GPIO type

Software Support

We provide a library for the AudioXover Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for AudioXover Click driver.

Standard key functions :

  • Config Object Initialization function.

    void audioxover_cfg_setup ( audioxover_cfg_t *cfg );

  • Initialization function.

    AUDIOXOVER_RETVAL audioxover_init ( audioxover_t ctx, audioxover_cfg_t cfg );

Example key functions :

  • Device power on function.

    void audioxover_power_on ( audioxover_t *ctx );

  • Device shut down function.

    void audioxover_shut_down ( audioxover_t *ctx );

Examples Description

This function initializes the driver and makes an initial log.

The demo application is composed of two sections :

Application Init

This function initializes and configures the Click and logger modules.


void application_init ( void )
{
    log_cfg_t log_cfg;
    audioxover_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    audioxover_cfg_setup( &cfg );
    AUDIOXOVER_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    audioxover_init( &audioxover, &cfg );
}

Application Task

This function enables and disables the Click board every 10 seconds, and logs an appropriate message on the USB UART.


void application_task ( void )
{
    log_printf( &logger, " * Switch: ON *\r\n" );
    audioxover_power_on ( &audioxover );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf( &logger, " * Switch: OFF *\r\n" );
    audioxover_shut_down ( &audioxover );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}  

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.AudioXover

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

IR Grid 3 Click

0

IR Grid 3 Click is a thermal imaging sensor. It has an array of 768 very sensitive, factory calibrated IR elements (pixels), arranged in 32 rows of 24 pixels, each measuring an object temperature up to 300˚C within its local Field of View (FOV). The MLX90640ESF-BAA IR sensor used on this Click board™ has only four pins, and it is mounted inside of the industry standard TO39 package.

[Learn More]

Opto Encoder 3 Click

0

Opto Encoder 3 Click is a linear incremental optical sensor/encoder Click, which can be used for the movement or rotation encoding.

[Learn More]

Mic Click

0

Mic Click carries the SPQ0410HR5H-B surface mount silicon microphone with maximum RF protection. The Click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over the AN pin on the mikroBUS™ line.

[Learn More]