H-Bridge 9 click

H-Bridge 9 Click is a compact add-on board that contains six MOSFET half-bridge outputs. This board features the L99UDL01, a six-channel half-bridge driver monolithic integrated circuit that is PWM configurable and current regulated from STMicroelectronics.

click Product page

Click library

• Author : Stefan Filipovic
• Date : Aug 2021.
• Type : SPI type

Software Support

We provide a library for the HBridge9 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for HBridge9 Click driver.

Standard key functions :

• hbridge9_cfg_setup Config Object Initialization function.

  void hbridge9_cfg_setup ( hbridge9_cfg_t *cfg );

• hbridge9_init Initialization function.

  err_t hbridge9_init ( hbridge9_t *ctx, hbridge9_cfg_t *cfg );

• hbridge9_default_cfg Click Default Configuration function.

  err_t hbridge9_default_cfg ( hbridge9_t *ctx );

Example key functions :

• hbridge9_write_register This function writes a desired data to the selected register.

  err_t hbridge9_write_register ( hbridge9_t *ctx, uint8_t reg, uint16_t data_in );

• hbridge9_read_register This function reads a desired data from the selected register.

  err_t hbridge9_read_register ( hbridge9_t *ctx, uint8_t reg, uint16_t *data_out );

• hbridge9_send_actuation_pulse This function sends an actuation pulse by toggling the ENO pin.

  void hbridge9_send_actuation_pulse ( hbridge9_t *ctx );

Example Description

This example demonstrates the use of H-Bridge 9 click board.

The demo application is composed of two sections :

Application Init

Initializes the driver and performs the click default configuration which will set the OUT1 to LOW, OUT2 to HIGH polarity, and the runtime to 1000ms.

void application_init ( void )
{
    log_cfg_t log_cfg;            /**< Logger config object. */
    hbridge9_cfg_t hbridge9_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.

    hbridge9_cfg_setup( &hbridge9_cfg );
    HBRIDGE9_MAP_MIKROBUS( hbridge9_cfg, MIKROBUS_1 );
    err_t init_flag = hbridge9_init( &hbridge9, &hbridge9_cfg );
    if ( SPI_MASTER_ERROR == init_flag )
    {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }

    init_flag = hbridge9_default_cfg ( &hbridge9 );
    if ( HBRIDGE9_ERROR == init_flag )
    {
        log_error( &logger, " Default Config Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }
    log_info( &logger, " Application Task " );
}

Application Task

Sends an actuation pulse every 5 seconds which will run the motor for a certain amount of time as set by default configuration.

void application_task ( void )
{
    hbridge9_send_actuation_pulse( &hbridge9 );
    log_printf( &logger, " Actuation pulse has been sent. \r\n\n" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

Note

The Voltage should be supplied with 6 to 18V power supply. Make sure to use a motor that operates in the above voltage range.

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.HBridge9

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.