We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: DMX
Downloaded: 71 times
Not followed.
License: MIT license
Download [549.03KB]DMX Click is a device used to establish communication between the MCU and equipment that uses the DMX512-A communication protocol.
[learn more]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: Motion
Downloaded: 102 times
Not followed.
License: MIT license
Download [581.26KB]Smart DOF 3 Click is a compact add-on board with a highly advanced integrated system-in-package (SIP) accelerometer and gyroscope sensors. This board features the ISM330IS, an iNEMO inertial module from STMicroelectronics. The inertial module consists of an always-on 3-axis accelerometer and 3-axis gyroscope with ISPU (intelligent sensor processing unit). In addition, the ISM330IS can be configured to allow connection with external I2C sensors.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 92 times
Not followed.
License: MIT license
Download [1.02MB]MCP2517FD Click is a complete CAN solution which carries the MCP2517FD CAN FD controller and ATA6563 high-speed CAN transceiver from Microchip, as well as a DB9 9-pin connector.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 134 times
Not followed.
License: MIT license
Download [1.03MB]MCP2518FD Click is a compact add-on board representing a complete CAN solution used as a control node in a CAN network. This board features the MCP2518FD, an external CAN FD controller with an SPI interface, and a high-speed CAN transceiver, the ATA6563, both from Microchip. The ATA6563, a low-level physical layer IC (PHY), provides a physical connection with the CAN bus itself, while the CAN controller MCP2518FD represents an interface between the MCU and the PHY. It features three operating modes with dedicated fail-safe features, remote wake-up via CAN, and ideally passive behavior when powered off on the CAN bus. This Click board™ is suitable for developing a wide range of automotive diagnostic applications, even on MCUs that do not natively support CAN interface.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: MP3
Downloaded: 101 times
Not followed.
License: MIT license
Download [697.59KB]MP3 Click is an accessory board in mikroBus™ form factor. It includes a stereo MP3 decoder chip VS1053 which can decode multiple formats (Ogg vorbis, MP3, MP1, MP2, MPEG4, WMA, FLAC, WAV, MIDI).
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: FM
Downloaded: 126 times
Not followed.
License: MIT license
Download [675.74KB]AM/FM 2 Click is a compact add-on board that can be used to listen to music from the AM and FM radio bands. This board features the Si4732, a broadcast AM/FM/SE/LW/RDS radio receiver from Skyworks. This radio receiver integrates the complete broadcast tuner and receiver function from antenna input to digital audio output. In addition to the radio receiver, this Click board™ is equipped with the LM4910, a Boomer output capacitor-less stereo 35mW headphone amplifier from Texas Instruments. This amplifier can deliver 35mW of continuous average power to a 32Ω load with less than 1% distortion.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: Measurements
Downloaded: 80 times
Not followed.
License: MIT license
Download [283.23KB]Wheatstone Click is a measurement Click board™ which utilizes a Wheatstone bridge circuit onboard, in order to precisely measure the resistance of an external element. Besides the wheatstone bridge circuit, this Click board™ also utilizes MAX4208 – an ultra-low offset/drift, precision instrumentation amplifier, from Maxim Integrated.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: Pressure
Downloaded: 113 times
Not followed.
License: MIT license
Download [336.34KB]Pressure 22 Click is a compact add-on board that contains a board-mount pressure sensor. This board features the MS5839-02BA, an ultra-compact chlorine-resistant digital pressure and temperature sensor from TE Connectivity. The sensor is a small digital altimeter operating from 300 up to 1200mbar, optimized for applications where chlorine and saline are present. The sensor is filled with gel, which makes it robust, and enables it to work in harsh environments.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: Motion
Downloaded: 93 times
Not followed.
License: MIT license
Download [521.87KB]Microwave 5 Click is a compact add-on board that utilizes the Doppler Shift Phenomenon to sense motion. This board features the PD-V10-G5, a miniature X-band microwave transceiver from Ningbo Pdlux Electronic Technology. The transmitter on this transceiver works on a 10.525GHz frequency over the patch antenna, with a 2-4kHz pulse repetition frequency. The strength of the sensor’s output, in other words, the detection range, depends on the Signal-to-Noise ratio.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 94 times
Not followed.
License: MIT license
Download [543.13KB]Charger 17 Click is a compact add-on board that provides a single-cell battery charging solution. This board features the RT9471, a 3A single-cell switching battery charger from Richtek. It is a highly-integrated battery charge and system power-path management device for single-cell Li-Ion and Li-Polymer batteries. The high-efficiency 1.5MHz synchronous switch-mode buck charger achieves up to 92% charge efficiency at 2A with 5V input and 3.8V battery.
[learn more] 
