We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: Buck
Downloaded: 49 times
Not followed.
License: MIT license
Download [454.15KB]Buck 22 Click is a compact add-on board that steps down the voltage from its input (supply) to its output (load). This board features the TPS62869, a high-frequency synchronous step-down converter with an I2C interface from Texas Instruments, providing an efficient, adaptive, and high power-density solution. The TPS62869 operates in PWM mode at medium to heavy loads (also for the slightest output voltage ripple), and it automatically enters Power-Save Mode operation at light load to maintain high efficiency over the entire output load current range. With its DCS-Control™ architecture, excellent load transient performance and tight output voltage accuracy are achieved alongside adjustable output voltage range from 0.8V to 3.35V with a 10mV step size.
[learn more]
Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.7
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 51 times
Not followed.
License: MIT license
Download [419.65KB]BATT-MON 2 Click is a compact add-on board representing a battery monitoring solution. This board features the MAX17262, an ultra-low power I2C-configurable fuel-gauge IC which implements the ModelGauge™ m5 algorithm from Analog Devices. The MAX17262 monitors a single-cell battery pack (best performance for batteries with 100mAhr to 6Ahr capacity), providing precision measurements of current, voltage, and temperature, and supporting internal current sensing for up to 3.1A pulse current. The battery pack's temperature is measured using an internal temperature sensor or external thermistor.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.4
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 51 times
Not followed.
License: MIT license
Download [572.63KB]Balancer 4 Click is a compact add-on board optimized for overvoltage protection balancing the voltage of serially connected batteries. This board features the MP2672A, a highly integrated, flexible switch-mode battery charger for Lithium-Ion batteries with two cells in series from Monolithic Power Systems (MPS). The MP2672A has a narrow voltage DC (NVDC) power structure and monitors the voltage across each cell, equalizing the cell�s voltages if the difference between the two cells exceeds the mismatch threshold. It also has two selective operating modes with configurable output current up to 2A via register setting via I2C serial interface, alongside selectable MP2672A power supply, LED indication, and protection features allowing a reliable operation.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: Buck
Downloaded: 48 times
Not followed.
License: MIT license
Download [451.61KB]Step Down 3 Click is a compact add-on board that steps down the voltage from its input to its output. This board features the ST1PS03, a nano-quiescent miniaturized synchronous step-down converter with a load switch from STMicroelectronics. The ST1PS03 can provide up to 400mA output current with an input voltage ranging from 1.8V to 5.5V, specifically designed for applications where high efficiency is crucial. It also embeds a controlled switch accessible from auxiliary channel input to supply a subsystem, output voltage from 1.6V to 3.3V set using three digital control inputs, and a Power Good signal to indicate stabilized output voltages.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 98 times
Not followed.
License: MIT license
Download [492.15KB]BATT-MON 4 Click is a compact add-on board representing an advanced battery monitoring solution. This board features the LTC3337, a primary battery state of health (SOH) monitor with a built-in precision coulomb counter from Analog Devices. The LTC3337 is designed to be placed in series with a primary battery with minimal associated series voltage drop. The patented infinite dynamic range coulomb counter tallies all accumulated battery discharge and stores it in an internal register accessible via an I2C interface. In addition, this Click board™ also can set the input current limit and has an additional discharge alarm interrupt and SOH monitoring which measures and reports via an I2C interface.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 82 times
Not followed.
License: MIT license
Download [525.63KB]BATT-MON 3 Click is a compact add-on board representing an advanced battery monitoring solution. This board features the BQ35100, battery fuel gauge, and end-of-service monitor from Texas Instruments. The BQ35100 provides highly configurable fuel gauging for non-rechargeable (primary) lithium batteries without requiring a forced battery discharge. It uses patented TI gauging algorithms to support the option to replace an old battery with a new one seamlessly. It provides accurate results with ultra-low average power consumption, alongside an I2C interface through which the host can read the gathered data.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Power Switch
Downloaded: 62 times
Not followed.
License: MIT license
Download [460.25KB]Current Limit 5 Click is a compact add-on board representing a current-limiting solution. This board features the MIC2099, a current-limit power distribution switch from Microchip Technology. This Click board™ represents a programmable current limit solution with various protection features and fault indication, which operates from a 2.5V to 5.5V input voltage range. Also, the current limit is adjustable from 100mA up to 1.05A programmed through the MCP4561 digital potentiometer. This Click board™ is suitable for applications in portable equipment and condition monitoring or power supplies, protecting them in short circuits or other overload conditions.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.9
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 69 times
Not followed.
License: MIT license
Download [551.45KB]Charger 18 Click is a compact add-on board representing a single-cell battery charger. This board features the LTC3553, a micropower, highly integrated power management, and battery charger for single-cell Li-Ion/Polymer battery applications from Analog Devices. Designed specifically for USB applications, it also includes a PowerPath manager with automatic load prioritization and input current limit, a battery charger, and numerous internal protection features. It also indicates a battery charge state, and it comes with a synchronous 200mA buck regulator and a 150mA low dropout linear regulator (LDO).
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Power Switch
Downloaded: 68 times
Not followed.
License: MIT license
Download [509.44KB]Current Limit 7 Click is a compact add-on board representing a current-limiting solution. This board features the MAX14575A, an adjustable current-limit switch from Analog Devices. This Click board™ features internal current limiting to prevent damage to host devices due to faulty load conditions, has a low 32mΩ on-resistance, and operates from a 2.3V to 5.5V input voltage range. Also, the current limit is adjustable from 250mA to 2.5A programmed through AD5272 digital rheostat and set via onboard range switch. This Click board™ is suitable for applications in portable equipment and condition monitoring or power supplies, protecting them in short circuits or other overload conditions.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: Buck-Boost
Downloaded: 64 times
Not followed.
License: MIT license
Download [668.07KB]BATT-MAN 2 Click is a compact add-on board representing an advanced battery and power management solution. This board features the MAX77654, a single inductor, multiple-output (SIMO) power management IC (PMIC) from Maxim Integrated, now part of Analog Devices. This I2C programmable board features a buck-boost regulator that provides three independently programmable power rails from a single inductor. Also, it has one 100mA LDO output with ripple rejection for audio and other noise-sensitive applications and a highly-configurable linear charger that supports a wide range of Li+ battery capacities featuring battery temperature monitoring for additional safety (JEITA).
[learn more] 
