We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.11
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 62 times
Not followed.
License: MIT license
Download [670.27KB]Charger 11 Click is a LiFePO4 (lithium iron phosphate) battery charger. This click can be used for Low-Cost LiFePO4 battery chargers, or Power Tools, toys, backup energy storage solutions, etc. Charger 11 is based on MCP73123T controller which has some extra features enabling charging without too much hassle. This click board has charging current control which uses SPI interface through MCP4161 IC, which is an 8-bit digital potentiometer.
[learn more]
Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.11
mikroSDK Library: 2.0.0.0
Category: USB-C PD
Downloaded: 105 times
Not followed.
License: MIT license
Download [699.14KB]USB-C Source Click is a compact add-on board that contains a standalone autonomous USB power delivery controller. This board features the STUSB4700, an independent USB power delivery controller optimized as a provider to negotiate a given amount of power to be sourced to an inquiring consumer device from STMicroelectronics.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.11
mikroSDK Library: 2.0.0.0
Category: USB-C PD
Downloaded: 113 times
Not followed.
License: MIT license
Download [540.60KB]USB-C Sink Click is a compact add-on board that contains a standalone autonomous USB power delivery controller. This board features the STUSB4500, a USB-C sink-only controller compatible with Power-Delivery (PD) from STMicroelectronics. It supports dead battery mode to allow a system to be powered from an external source directly, establishes a valid source-to-sink connection, and negotiates a USB power delivery (PD) contract with a PD capable source device.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.9
mikroSDK Library: 2.0.0.0
Category: Power Switch
Downloaded: 52 times
Not followed.
License: MIT license
Download [603.47KB]eFuse 2 Click is a compact add-on board that contains an integrated FET hot-swap device. This board features the TPS259631, a highly integrated circuit protection and power management solution from Texas Instruments. It provides multiple protection modes against overloads, short circuits, voltage surges, and excessive inrush current.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.15
mikroSDK Library: 2.0.0.0
Category: Power Switch
Downloaded: 68 times
Not followed.
License: MIT license
Download [488.49KB]Current Limit Click is a compact add-on board that contains a low-voltage, P-channel MOSFET power switch intended for high-side load switching applications. This board features the MAX890L, a low-resistance power switch with the adjustable, accurate current limit system, and thermal shutdown from Maxim Integrated.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: Power Switch
Downloaded: 89 times
Not followed.
License: MIT license
Download [438.67KB]Fuse Click is a compact add-on board that contains a programmable electronic power breaker. This board features the STPW12, an integrated electronic power breaker optimized to monitor the input power from STMicroelectronics. Connected in series to the power rail, it can disconnect the electronic circuitry on its output if the power consumption overcomes the programmed limit. The intervention of the protection is communicated to the MCU through a signal on the fault pin. The device can also be enabled/disabled through a dedicated Enable pin with a direct PWM mode, which can be achieved through an external PWM signal.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.12
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 67 times
Not followed.
License: MIT license
Download [474.14KB]Charger 16 Click is a compact add-on board that represents a single-cell battery charger. This board features the LT1571, a constant-current/constant-voltage battery charger with preset voltage and termination flag from Analog Devices.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.12
mikroSDK Library: 2.0.0.0
Category: Buck
Downloaded: 49 times
Not followed.
License: MIT license
Download [446.01KB]Buck 10 Click is a high-efficiency step-down converter which provides a highly regulated output voltage derived from the connected power source, rated from 4V to 18V. The regulated output voltage can be selected between two values: 3.3V and 5V. These are voltage values that are most commonly used in many embedded designs. This click is based around an integrated DC-DC converter, labeled as MPM3632C.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.11
mikroSDK Library: 2.0.0.0
Category: Buck
Downloaded: 64 times
Not followed.
License: MIT license
Download [474.24KB]Buck 9 Click is a high-efficiency step-down converter which provides a highly regulated output voltage derived from the connected power source, rated from 4V to 36V. The regulated output voltage can be selected between two values: 3.3V and 5V. These are voltage values that are most commonly used in many embedded designs. Buck 9 click is based around an integrated DC-DC converter, labeled as MP9943.
[learn more] Author: MIKROE
Last Updated: 2024-04-03
Package Version: 2.1.0.8
mikroSDK Library: 2.0.0.0
Category: Buck-Boost
Downloaded: 55 times
Not followed.
License: MIT license
Download [623.51KB]Buck & Boost Click is a compact add-on board that contains a configurable power management device. This board features the MIC7401, a highly-integrated power-management IC featuring five synchronous buck regulators, one boost regulator, and a high-speed I2C interface with an internal EEPROM memory from Microchip.
[learn more] 
