We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Rating:
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.16
mikroSDK Library: 2.0.0.0
Category: Pushbutton/Switches
Downloaded: 190 times
Not followed.
License: MIT license
Joystick Click is a smart navigation key concept based on contactless, magnetic movement detection.
Do you want to subscribe in order to receive notifications regarding "Joystick Click" changes.
Do you want to unsubscribe in order to stop receiving notifications regarding "Joystick Click" changes.
Do you want to report abuse regarding "Joystick Click".
DOWNLOAD LINK | RELATED COMPILER | CONTAINS |
---|---|---|
3327_joystick_click.zip [473.62KB] | mikroC AI for ARM GCC for ARM Clang for ARM mikroC AI for PIC mikroC AI for PIC32 XC32 GCC for RISC-V Clang for RISC-V mikroC AI for AVR mikroC AI for dsPIC XC16 |
|
Joystick Click is a smart navigation key concept based on contactless, magnetic movement detection.
We provide a library for the Joystick Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.
This library contains API for Joystick Click driver.
Config Object Initialization function.
void joystick_cfg_setup ( joystick_cfg_t *cfg );
Initialization function.
JOYSTCIK_RETVAL joystick_init ( joystick_t ctx, joystick_cfg_t cfg );
Click Default Configuration function.
void joystick_default_cfg ( joystick_t *ctx );
Get joystick position function
uint8_t joystick_get_position( joystick_t *ctx );
Get state of Joystick button function
uint8_t joystick_press_button( joystick_t *ctx );
General soft reset function
void joystick_soft_reset( joystick_t *ctx );
This application configures and enables use of the joystick.
The demo application is composed of two sections :
Initialization driver enables - device, sets default configuration and starts write log.
void application_init ( void )
{
log_cfg_t log_cfg;
joystick_cfg_t cfg;
/**
* Logger initialization.
* Default baud rate: 115200
* Default log level: LOG_LEVEL_DEBUG
* @note If USB_UART_RX and USB_UART_TX
* are defined as HAL_PIN_NC, you will
* need to define them manually for log to work.
* See @b LOG_MAP_USB_UART macro definition for detailed explanation.
*/
LOG_MAP_USB_UART( log_cfg );
log_init( &logger, &log_cfg );
log_info( &logger, "---- Application Init ----" );
// Click initialization.
joystick_cfg_setup( &cfg );
JOYSTCIK_MAP_MIKROBUS( cfg, MIKROBUS_1 );
joystick_init( &joystick, &cfg );
Delay_100ms( );
joystick_default_cfg( &joystick );
log_printf( &logger, "*********************\r\n" );
log_printf( &logger, " Configuration \r\n" );
log_printf( &logger, "*********************\r\n" );
log_printf( &logger, " Joystick Click \r\n" );
log_printf( &logger, "*********************\r\n" );
Delay_100ms( );
}
This is a example which demonstrates the use of Joystick Click board. Joystick Click communicates with register via I2C by write and read from register, read joystick position and press button state. Results are being sent to the Usart Terminal where you can track their changes. All data logs on usb uart when the sensor is triggered.
void application_task ( void )
{
// Task implementation.
button_state = joystick_press_button( &joystick );
position = joystick_get_position( &joystick );
Delay_10ms( );
if ( ( button_state == 1 ) && ( button_state_old == 0 ) )
{
button_state_old = 1;
log_printf( &logger, " Button is pressed \r\n" );
log_printf( &logger, "*********************\r\n" );
}
if ( ( button_state == 0 ) && ( button_state_old == 1 ) )
{
button_state_old = 0;
}
if ( position_old != position )
{
switch ( position )
{
case 0 :
{
log_printf( &logger," Start position \r\n" );
break;
}
case 1 :
{
log_printf( &logger, " Top \r\n" );
break;
}
case 2 :
{
log_printf( &logger, " Top-Right \r\n" );
break;
}
case 3 :
{
log_printf( &logger, " Right \r\n" );
break;
}
case 4 :
{
log_printf( &logger, " Bottom-Right \r\n" );
break;
}
case 5 :
{
log_printf( &logger, " Bottom \r\n" );
break;
}
case 6 :
{
log_printf( &logger, " Bottom-Left \r\n" );
break;
}
case 7 :
{
log_printf( &logger, " Left \r\n" );
break;
}
case 8 :
{
log_printf( &logger, " Top-Left \r\n" );
break;
}
}
log_printf( &logger, "*********************\r\n" );
position_old = position;
Delay_100ms();
}
}
The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.
Other mikroE Libraries used in the example:
Additional notes and informations
Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.