TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141320 times)
  2. FAT32 Library (74154 times)
  3. Network Ethernet Library (58737 times)
  4. USB Device Library (48834 times)
  5. Network WiFi Library (44544 times)
  6. FT800 Library (44120 times)
  7. GSM click (30857 times)
  8. mikroSDK (29699 times)
  9. PID Library (27359 times)
  10. microSD click (27273 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

Buck 8 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.18

mikroSDK Library: 2.0.0.0

Category: Buck

Downloaded: 301 times

Not followed.

License: MIT license  

Buck 8 Click is a high efficiency, wide voltage range, and high current synchronous step down (buck) DC-DC converter, featuring two enhanced modes that can be used to drive lighter loads with increased efficiency.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "Buck 8 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "Buck 8 Click" changes.

Do you want to report abuse regarding "Buck 8 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


Buck 8 Click

Buck 8 Click is a high efficiency, wide voltage range, and high current synchronous step down (buck) DC-DC converter, featuring two enhanced modes that can be used to drive lighter loads with increased efficiency.

buck8_click.png

Click Product page


Click library

  • Author : Katarina Perendic
  • Date : nov 2019.
  • Type : GPIO type

Software Support

We provide a library for the Buck8 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for Buck8 Click driver.

Standard key functions :

  • Config Object Initialization function.

    void buck8_cfg_setup ( buck8_cfg_t *cfg );

  • Initialization function.

    BUCK8_RETVAL buck8_init ( buck8_t ctx, buck8_cfg_t cfg );

  • Click Default Configuration function.

    void buck8_default_cfg ( buck8_t *ctx );

Example key functions :

  • Get state of pin

    uint8_t buck8_get_state ( buck8_t *ctx );

  • Function settings mode

    void buck8_set_power_mode ( buck8_t *ctx, uint8_t mode );

Examples Description

Demo application shows basic usage of BUCK 8 clicks.

The demo application is composed of two sections :

Application Init

Configures the driver and enables the Click board.

void application_init ( void )
{
    log_cfg_t log_cfg;
    buck8_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    buck8_cfg_setup( &cfg );
    BUCK8_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    buck8_init( &buck8, &cfg );

    buck8_default_cfg( &buck8 );
}

Application Task

Reads the VOUT state and parses it on USB UART.

void application_task ( void )
{
    uint8_t pg_state;

    pg_state = buck8_get_state( &buck8 );

    if ( pg_state == 1 )
    {
        log_info( &logger, "VOUT is below 92.2%% of VIN" );
    }
    else
    {
        log_info( &logger, "VOUT is above 92.2%% of VIN" );
    }

    Delay_1sec();
}

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.Buck8

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

Oximeter click

5

Oximeter click is a versatile photometric Click board, perfectly suited for measuring the blood oxygen saturation. It employs ADPD105, a highly configurable photometric front end (AFE) device from Analog Devices.

[Learn More]

Thermo 16 click

5

Thermo 16 Click is a Click board™ equipped with the sensor IC, which can measure temperature measurements between -40°C and +150°C so that the temperature measurement data can be processed by the host MCU.

[Learn More]

Charger 27 Click

0

Charger 27 Click is a compact add-on board that provides a single-cell charging solution. This board features the MP2639B, a Li-Ion or Li-Polymer switching charger from MPS. It is a highly integrated, flexible switch-mode battery charging management device for a single-cell battery for various portable applications. It uses a 4.5V up to 16V external input voltage to provide up to 2A of programmable charging current.

[Learn More]