Code Categories

All codes (5055)

TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (142156 times)
  2. FAT32 Library (75476 times)
  3. Network Ethernet Library (59606 times)
  4. USB Device Library (49619 times)
  5. Network WiFi Library (45371 times)
  6. FT800 Library (45081 times)
  7. GSM click (31490 times)
  8. mikroSDK (30592 times)
  9. microSD click (27907 times)
  10. PID Library (27645 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

LCD Demo

Rating:

0

Author: MIKROE

Last Updated: 2024-07-09

Package Version: 2.0.0.5

mikroSDK Library: 2.0.0.0

Category: LCD

Downloaded: 279 times

Not followed.

License: MIT license  

The application demonstrates LCD functionality.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "LCD Demo" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "LCD Demo" changes.

Do you want to report abuse regarding "LCD Demo".

  • Information
  • Comments (0)

mikroSDK Library Blog

Product link

LCD DEMO

This example demonstrates LCD library functionalities. In this demo, the text will quickly show on LCD display, after clearing this text, new text will show in two rows and it will move to the left and right in a loop.

  • Author : MIKROE
  • Version : 2.0.0.5
  • Date : July 2024.

Hardware Support

  • Put LCD display into LCD socket.
    • image
  • Put LCD switches in ON position.
    • image

Software Support

We provide demo code for demonstrating LCD library functionalities. To run this example, follow these steps:

  1. Install the package from Package manager.
  2. Open example.
  3. It will take you to setups, so make one for your hardware.
  4. Choose adequate setup and the project will open.
  5. Program it by clicking on Flash.
  6. Text should appear on LCD display.
  7. Once the text LCD_demo mikroeElektronika is on display, text should move to the left then right.

ALSO FROM THIS AUTHOR

Motion 2 Click

0

Motion 2 Click is a Click board™ based on EKMC1607112, PIR motion sensor from Panasonic Corporation that's used as human motion detector. Also featured on Motion 2 Click bord is TLP241A photorelay from Toshiba that is used to provide a reinforced galvanic isolation for the external signals used to drive some external high power electronic equipment when motion is detected. It's allowing up to 40V between the SSR contacts in OFF state, and currents up to 2A while in ON state, thanks to a very low ON-state resistance. Motion 2 Click board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

[Learn More]

Headphone AMP 2 Click

0

Headphone AMP 2 Click is a compact add-on board that contains a stereo headphone amplifier. This board features the MAX9723, a stereo DirectDrive headphone amplifier with BassMax, volume control, and I2C from Analog Devices. The amplifier delivers 62mW into a 16Ω load, and features a high 90dB PSRR at 1KHz and a low 0.006% THD+N. It also features an integrated 32-level volume control, Click-and-pop suppression, ±8kV HBM ESD-protected headphone outputs, short-circuit and thermal-overload protection, and more.

[Learn More]

Brushless 7 Click

0

Brushless 7 Click is, as its name said, a motor driver based expansion board for controlling BLCD motors with any microcontroller.

[Learn More]

embeddedwiki libstock