TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141304 times)
  2. FAT32 Library (74107 times)
  3. Network Ethernet Library (58718 times)
  4. USB Device Library (48831 times)
  5. Network WiFi Library (44526 times)
  6. FT800 Library (44078 times)
  7. GSM click (30834 times)
  8. mikroSDK (29673 times)
  9. PID Library (27357 times)
  10. microSD click (27251 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

AN to PWM 2 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.4

mikroSDK Library: 2.0.0.0

Category: ADC

Downloaded: 98 times

Not followed.

License: MIT license  

AN to PWM 2 Click is a compact add-on board that contains an easy-to-use component that converts the value of the input analog signal to a fixed frequency PWM voltage output, with a duty cycle proportional to the input voltage. This board features the LTC6992CS6, a silicon oscillator with an easy-to-use analog voltage-controlled pulse width modulation (PWM) capability from Analog Devices. It features the PWM signal controlled by analog input in range of -2.5V to 2.5V, frequency range up to 1 MHz, frequency error less than 1.7%, and it has good temperature stability. It has many features that make it well suited for heater control, PWM servo loops, LED dimming, signal isolation, and other duty cycle control applications.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "AN to PWM 2 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "AN to PWM 2 Click" changes.

Do you want to report abuse regarding "AN to PWM 2 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


AN to PWM 2 Click

AN to PWM 2 Click is a compact add-on board that contains an easy-to-use component that converts the value of the input analog signal to a fixed frequency PWM voltage output, with a duty cycle proportional to the input voltage. This board features the LTC6992CS6, a silicon oscillator with an easy-to-use analog voltage-controlled pulse width modulation (PWM) capability from Analog Devices. It features the PWM signal controlled by analog input in range of -2.5V to 2.5V, frequency range up to 1 MHz, frequency error less than 1.7%, and it has good temperature stability. It has many features that make it well suited for heater control, PWM servo loops, LED dimming, signal isolation, and other duty cycle control applications.

antopwm2_click.png

Click Product page


Click library

  • Author : Stefan Filipovic
  • Date : Feb 2024.
  • Type : I2C type

Software Support

We provide a library for the AN to PWM 2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for AN to PWM 2 Click driver.

Standard key functions :

  • antopwm2_cfg_setup Config Object Initialization function.

    void antopwm2_cfg_setup ( antopwm2_cfg_t *cfg );
  • antopwm2_init Initialization function.

    err_t antopwm2_init ( antopwm2_t *ctx, antopwm2_cfg_t *cfg );

Example key functions :

  • antopwm2_set_frequency This function sets a frequency output in a range from 500kHz to 1MHz by setting the digipot resistance.

    err_t antopwm2_set_frequency ( antopwm2_t *ctx, uint32_t freq );
  • antopwm2_set_frequency_otp This function sets a frequency output in a range from 500kHz to 1MHz by setting the digipot resistance in OTP mode.

    err_t antopwm2_set_frequency_otp ( antopwm2_t *ctx, uint32_t freq );

Example Description

This example demonstrates the use of AN to PWM 2 Click board by changing the PWM output frequency from 500kHz to 1MHz in steps of 50kHz.

The demo application is composed of two sections :

Application Init

Initializes the driver and logger.


void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    antopwm2_cfg_t antopwm2_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    antopwm2_cfg_setup( &antopwm2_cfg );
    ANTOPWM2_MAP_MIKROBUS( antopwm2_cfg, MIKROBUS_1 );
    if ( I2C_MASTER_ERROR == antopwm2_init( &antopwm2, &antopwm2_cfg ) ) 
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }

    log_info( &logger, " Application Task " );
}

Application Task

Changes the PWM output frequency every 5 seconds in steps of 50kHz going through the full range from 500kHz to 1MHz. The currently set frequency will be displayed on the USB UART.

void application_task ( void )
{
    static uint32_t freq = ANTOPWM2_FREQ_MIN;
    if ( ANTOPWM2_OK == antopwm2_set_frequency ( &antopwm2, freq ) )
    {
        log_printf ( &logger, " Frequency: %lu Hz\r\n\n", freq );
    }
    freq += 50000;
    if ( freq > ANTOPWM2_FREQ_MAX )
    {
        freq = ANTOPWM2_FREQ_MIN;
    }
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

Note

Applying a voltage of -2.5 to 2.5V on the input will generate the PWM pulse train with a duty cycle linearly proportional to the input voltage.

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.ANtoPWM2

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.


ALSO FROM THIS AUTHOR

Angle 10 Click

0

Angle 10 Click is a compact add-on board that detects the absolute angular position of a permanent magnet. This board features the AS5070A, a high-resolution angular position sensor with an analog output for precise absolute angle measurement from ams AG. Based on a Hall sensor technology, the AS5070A measures the orthogonal component of the flux density over a full-turn rotation and compensates for external stray magnetic fields with a robust architecture based on a 14-bit sensor array and analog front-end. Only a simple two-pole magnet rotating over the center of the AS5070A is required to measure the angle, providing an instant indication of the magnet’s angular position.

[Learn More]

RTC 5 Click

1

RTC5 Click carries MCP79510, a real-time clock/calendar with an SPI interface (mikroBUS MISO, MOSI, SCK and CS pins); along with a programmable interrupt for system output.

[Learn More]

Motion 3 click

5

Motion 3 Click is a Click board based on EKMC1606112, PIR motion sensor from Panasonic Corporation that's used as human motion detector.

[Learn More]