We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.18
mikroSDK Library: 2.0.0.0
Category: Port expander
Downloaded: 224 times
Not followed.
License: MIT license
Download [553.34KB]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.19
mikroSDK Library: 2.0.0.0
Category: SPI
Downloaded: 250 times
Not followed.
License: MIT license
Download [511.06KB]The Click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI interface.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.17
mikroSDK Library: 2.0.0.0
Category: Port expander
Downloaded: 284 times
Not followed.
License: MIT license
Download [608.15KB]EXPAND 2 Click is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23017 with I²C clock speeds up to 10 MHz for higher throughput applications.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 198 times
Not followed.
License: MIT license
Download [506.56KB]ATA6570 Click is a CAN Partial Networking interface board. The Click carries the ATA6570, a high-speed CAN transceiver that interfaces a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.18
mikroSDK Library: 2.0.0.0
Category: Current
Downloaded: 318 times
Not followed.
License: MIT license
Download [508.74KB] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: RS485
Downloaded: 363 times
Not followed.
License: MIT license
Download [356.44KB]The RS485 5 Click is a Click board™ equipped with the MAX485, low-power, slew-rate-limited transceiver for RS-485 and RS-422 communication, from Maxim Integrated. This device supports half-duplex RS-485 communication and can be used as an interface between the TTL level UART and the RS485 communication bus.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: RS485
Downloaded: 243 times
Not followed.
License: MIT license
Download [375.68KB]RS485 6 Click offers a half-duplex RS-485 communication with integrated surge protection
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.18
mikroSDK Library: 2.0.0.0
Category: RS485
Downloaded: 259 times
Not followed.
License: MIT license
Download [423.04KB]RS485 4 Click offers an UART to RS485 signal conversion, featuring the ADM2795E specialized IC with the complete galvanic isolation.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.22
mikroSDK Library: 2.0.0.0
Category: RS485
Downloaded: 225 times
Not followed.
License: MIT license
Download [450.85KB]RS485 3 Click is an RS422/485 transceiver Click board™, which can be used as an interface between the TTL level UART and the RS422/485 communication bus.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 233 times
Followed by: 1 user
License: MIT license
Download [548.05KB]OBDII Click offers a unique opportunity to tap into the car diagnostic systems. It features the STN1110 Multiprotocol OBD to UART Interface, developed by the ScanTool technologies. This Click can be used for the communication with the Electronic Control Unit (ECU) of a vehicle, via several different OBD II diagnostic protocols such as CAN, K LINE, L LINE and J1850. The STN1110 IC is used to process requests sent by the MCU via the UART interface and return back the responses from the ECU network nodes.
[learn more] 
