We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.3
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 49 times
Not followed.
License: MIT license
Download [524.00KB]Stepper 3 Click is designed to drive unipolar stepper motors, with a supply voltage applied to the common wire. The current flows through the common wire and the motor coil, via the activated current sink driver, to the ground. This Click board™ uses the ULN2003A, a high voltage and current Darlington transistors array IC, as the sink driver. This IC is an ideal solution for this purpose, as it has seven high power Darlington output stages, activated by TTL/CMOS logic level signals, applied to the control pins. This allows driving unipolar stepper motors with up to 30V and 500mA per coil.
[learn more]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.3
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 44 times
Not followed.
License: MIT license
Download [638.22KB]Silent Step Click is the complete integrated bipolar step motor driver solution, rich with many features that allow extremely smooth and silent operation of the connected motor while being able to provide up to 2.5A peak motor current and withstand up to 46V supply voltage. The specialized TMC5130 IC driver from Trinamic Company far exceeds the capabilities of similar step motor drivers that are commonly used.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.3
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 44 times
Not followed.
License: MIT license
Download [647.71KB]Silent Step 3 Click is the complete integrated bipolar step motor driver solution, rich with many features that allow extremely smooth and silent operation of the connected motor while being able to provide up to 4A peak motor current and withstand up to 30V supply voltage. The specialized TMC2660 IC driver from Trinamic company far exceeds the capabilities of similar step motor drivers that are commonly used.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.3
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 63 times
Not followed.
License: MIT license
Download [511.84KB]Stepper 2 Click is a complete solution for driving bipolar stepper motors with full/half and micro-steps. It features the A4988 IC from Allegro Microsystems with DMOS low RDSON drivers on its outputs, which ensure high efficiency and reliable operation of the internal H-Bridges. This IC has the integrated translator section, used to simplify the control: using simple step control inputs from the host MCU, the stepper motor can be driven in both directions, with the predetermined step sizes. In addition, the output current is regulated allowing for noiseless operation of the stepper motor, with no resonance and ringing typically observed at unregulated stepper driver designs.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.3
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 53 times
Not followed.
License: MIT license
Download [535.85KB]Stepper Click is a complete solution for driving bipolar stepper motors with full/half and micro-steps. It features the A3967 IC from Allegro Microsystems with proprietary Satlington™ sink drivers on its outputs, which ensure high efficiency and reliable operation of the internal H-Bridges. This IC has the integrated translation section, used to simplify the control: using simple step control inputs from the host MCU, the stepper motor can be driven in both directions, with the predetermined step sizes. In addition, the output current is regulated allowing for noiseless operation of the stepper motor, with no resonance and ringing typically observed at unregulated stepper driver designs.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.4
mikroSDK Library: 2.0.0.0
Category: Brushed
Downloaded: 44 times
Not followed.
License: MIT license
Download [512.71KB]H-Bridge Click is a high-efficiency dual H-bridge driver Click board™, capable of providing reasonably high current while driving the connected load with up to 7V. Since the used driver IC has two full H-bridge channels, this Click board™ is an ideal solution for driving smaller bipolar stepper motors. H-Bridge Click provides driving in both directions, with an addition of the brake mode, and the high impedance mode (Hi-Z). Overshoot current suppression algorithm protects the output stages from being damaged if both high-side and low-side MOSFETs on a single H-bridge channel become conductive.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 66 times
Not followed.
License: MIT license
Download [632.74KB]Silent Step 4 Click is a compact add-on board representing a completely integrated step motor driver solution. This board features the TMC2240, a smart integrated stepper driver from Analog Devices. The driver is based on a 256 micro-steps built-in indexer, two fully integrated H-Bridges, and non-dissipative integrated current sensing (ICS). The two H-Bridges can drive motors of up to 36V and 3A at max.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 101 times
Not followed.
License: MIT license
Download [697.82KB]Silent Step 2 Click is a compact add-on board that allows extremely smooth and silent operation of the connected motor. This board features the TMC2130, a high-performance two-phase stepper motor driver from Analog Devices. The driver uses an external motor power supply of 4.75 up to 43V to power a 2-phase stepper motor up to 2A coil current (2.5A peak).
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.6
mikroSDK Library: 2.0.0.0
Category: Brushed
Downloaded: 104 times
Not followed.
License: MIT license
Download [606.05KB]H-Bridge 16 Click is a compact add-on board with an H-Bridge gate driver, also known as a full-bridge pre-driver. This board features the DRV8262, a dual H-Bridge motor driver from Texas Instruments. The motor driver is designed for a variety of industrial applications and can drive one or two brushed DC motors, one stepper motor, and one or two thermoelectric coolers (TEC). It can operate in a wide supply voltage range of 4.5V to 65V.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.5
mikroSDK Library: 2.0.0.0
Category: Brushed
Downloaded: 65 times
Not followed.
License: MIT license
Download [585.00KB]H-Bridge 15 Click is a compact add-on board with an H-Bridge gate driver, also known as a full-bridge pre-driver. This board features the DRV8834, a dual-bridge stepper or DC motor driver from Texas Instruments.
[learn more] 
