TOP Contributors

  1. MIKROE (2784 codes)
  2. Alcides Ramos (405 codes)
  3. Shawon Shahryiar (307 codes)
  4. jm_palomino (133 codes)
  5. Bugz Bensce (97 codes)
  6. S P (73 codes)
  7. dany (71 codes)
  8. MikroBUS.NET Team (35 codes)
  9. NART SCHINACKOW (34 codes)
  10. Armstrong Subero (27 codes)

Most Downloaded

  1. Timer Calculator (141837 times)
  2. FAT32 Library (74959 times)
  3. Network Ethernet Library (59321 times)
  4. USB Device Library (49312 times)
  5. Network WiFi Library (45109 times)
  6. FT800 Library (44676 times)
  7. GSM click (31290 times)
  8. mikroSDK (30236 times)
  9. microSD click (27664 times)
  10. PID Library (27565 times)
Libstock prefers package manager

Package Manager

We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]

< Back
mikroSDK Library

VCP Monitor 2 Click

Rating:

0

Author: MIKROE

Last Updated: 2024-10-31

Package Version: 2.1.0.17

mikroSDK Library: 2.0.0.0

Category: Measurements

Downloaded: 400 times

Not followed.

License: MIT license  

VCP Monitor 2 Click is a three-channel, high-side current and bus voltage monitor with alert indication function ensuring the intended application works within desired operating conditions. Featured chip INA3221-Q1, by Texas Instruments, monitors both shunt voltage drops and bus supply voltages, in addition to having programmable conversion times and averaging modes for these signals.

No Abuse Reported

Do you want to subscribe in order to receive notifications regarding "VCP Monitor 2 Click" changes.

Do you want to unsubscribe in order to stop receiving notifications regarding "VCP Monitor 2 Click" changes.

Do you want to report abuse regarding "VCP Monitor 2 Click".

  • mikroSDK Library 1.0.0.0
  • Comments (0)

mikroSDK Library Blog


VCP Monitor 2 Click

VCP Monitor 2 Click is a three-channel, high-side current and bus voltage monitor with alert indication function ensuring the intended application works within desired operating conditions. Featured chip INA3221-Q1, by Texas Instruments, monitors both shunt voltage drops and bus supply voltages, in addition to having programmable conversion times and averaging modes for these signals.

vcpmonitor2_click.png

Click Product page


Click library

  • Author : MikroE Team
  • Date : Jun 2020.
  • Type : I2C type

Software Support

We provide a library for the Vcpmonitor2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for Vcpmonitor2 Click driver.

Standard key functions :

  • Config Object Initialization function.

    void vcpmonitor2_cfg_setup ( vcpmonitor2_cfg_t *cfg );

  • Initialization function.

    VCPMONITOR2_RETVAL vcpmonitor2_init ( vcpmonitor2_t ctx, vcpmonitor2_cfg_t cfg );

Example key functions :

  • Get Manufacture ID.

    uint16_t vcpmonitor2_get_manifacture_id ( vcpmonitor2_t *ctx );

  • Get DIE ID.

    uint16_t vcpmonitor2_get_die_id ( vcpmonitor2_t *ctx );

  • Get BUS voltage in mV.

    float vcpmonitor2_get_bus_voltage ( vcpmonitor2_t *ctx, uint8_t channel );

Examples Description

VCP Monitor 2 Click is a three-channel, high-side current and bus voltage monitor with alert indication function ensuring the intended application works within desired operating conditions.

The demo application is composed of two sections :

Application Init

Initiaizes the driver, and checks the communication by reading the manufacture device ID. After that, performs the device default configuration.


void application_init ( void )
{
    log_cfg_t log_cfg;
    vcpmonitor2_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    vcpmonitor2_cfg_setup( &cfg );
    VCPMONITOR2_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    vcpmonitor2_init( &vcpmonitor2, &cfg );

    check_id = vcpmonitor2_get_manifacture_id( &vcpmonitor2 );
    if ( check_id == VCPMONITOR2_DEF_MANUFACTURE_ID )
    {
        log_printf( &logger, ">> Manufacture ID: 0x%.4X\r\n", check_id );
    }
    else
    {
        log_error( &logger, " WRONG ID READ! " );
        log_printf( &logger, "Please restart your system.\r\n" );
        for ( ; ; );
    }

    vcpmonitor2_default_cfg( &vcpmonitor2 );
}

Application Task

Displays the voltage, current, and power detected from channel 1 on the USB UART every 2 seconds. It also displays the status of alert indicators.


void application_task ( void )
{
    log_printf( &logger, ">> CHANNEL 1 <<\r\n" );
    display_channel_data( VCPMONITOR2_CHANNEL_1 );

    display_alert_status( );
    log_printf( &logger, "--------------------------\r\n" );

    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}  

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

  • MikroSDK.Board
  • MikroSDK.Log
  • Click.Vcpmonitor2

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.


ALSO FROM THIS AUTHOR

NeoMesh 868MHz Click

0

NeoMesh Click - 868MHz is a compact add-on board with a low-power, long-range transceiver, ideal for Mesh wireless networking. This board features the NC1000C-8, a wireless Mesh network module from NeoCortec. With an additional antenna that MikroE offers connected to the module’s u.Fl connector, you can create a fully functional wireless Mesh network node that will work in the Sub-GHz frequency band of 868MHz. The module has a generic application layer that can configured to suit applications.

[Learn More]

MCP16331 INV click

5

MCP16331 INV click works as a buck-boost voltage regulator, a type of switching mode power supply topology that combines the principles of the buck conversion (step-down) and the boost conversion (step-up) integrated on a single device.

[Learn More]

LBAND RTK Click

0

LBAND RTK Click is a compact add-on board that provides global and easy access to satellite L-Band GNSS corrections. This board features the NEO-D9S-00B, an professional-grade satellite data receiver for L-band correction broadcast from u-blox. Operating in a frequency range from 1525MHz to 1559MHz, the NEO-D9S-00B decodes the satellite transmission and outputs a correction stream, enabling a high-precision GNSS receiver to reach accuracies down to centimeter level. It can also select the GNSS correction data delivery channel alongside advanced security features such as signature and anti-jamming.

[Learn More]