We strongly encourage users to use Package manager for sharing their code on Libstock website, because it boosts your efficiency and leaves the end user with no room for error. [more info]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.13
mikroSDK Library: 2.0.0.0
Category: CAN
Downloaded: 396 times
Not followed.
License: MIT license
Download [1.03MB]MCP251863 Click is a compact add-on board representing a complete CAN solution used as a control node in a CAN network. This board features the MCP251863, IC representing a compact solution with a controller and a transceiver in one package, the MCP2518FD and ATA6563 from Microchip. The ATA6563, a low-level physical layer IC (PHY), provides a physical connection with the CAN bus itself, while the CAN controller MCP2518FD represents an interface between the MCU and the PHY. It features three operating modes with dedicated fail-safe features, remote wake-up via CAN, and ideally passive behavior when powered off on the CAN bus. This Click board™ is suitable for developing a wide range of automotive diagnostic applications, even on MCUs that don’t support CAN interface.
[learn more]
Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Pressure
Downloaded: 172 times
Not followed.
License: MIT license
Download [430.04KB]Barometer 8 Click is a compact add-on board used to measure air pressure in a specific environment. This board features the ILPS22QS, an ultra-compact piezoresistive absolute pressure sensor that functions as a digital output barometer from STMicroelectronics. The ILPS22QS comprises a sensing element and an IC chip for signal processing in one package, converts pressure into a 24-bit digital value, and sends the information via a configurable host interface that supports SPI and I2C serial communications. It has a selectable dual full-scale absolute pressure range, up to 1260hPa and 4060hPa, with an accuracy of 0.5hPa over a wide operating temperature range.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.15
mikroSDK Library: 2.0.0.0
Category: Battery Charger
Downloaded: 165 times
Not followed.
License: MIT license
Download [525.80KB]BATT-MON 3 Click is a compact add-on board representing an advanced battery monitoring solution. This board features the BQ35100, battery fuel gauge, and end-of-service monitor from Texas Instruments. The BQ35100 provides highly configurable fuel gauging for non-rechargeable (primary) lithium batteries without requiring a forced battery discharge. It uses patented TI gauging algorithms to support the option to replace an old battery with a new one seamlessly. It provides accurate results with ultra-low average power consumption, alongside an I2C interface through which the host can read the gathered data.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.11
mikroSDK Library: 2.0.0.0
Category: Digital potentiometer
Downloaded: 245 times
Not followed.
License: MIT license
Download [476.41KB]DIGI POT 9 Click is a compact add-on board used as a digitally controlled potentiometer. This board features the AD5235, a dual-channel, nonvolatile memory, digitally controlled potentiometer from Analog Devices. The AD5235's versatile programming via an SPI-compatible serial interface allows multiple modes of operation and adjustment. The resistor wiper position is determined by the RDAC register contents, which act as a scratchpad register, allowing unlimited changes of resistance settings. The nominal resistance of the RDAC between terminal A and terminal B (RAB) is 250 kΩ with 1024 positions (10-bit resolution).
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 131 times
Not followed.
License: MIT license
Download [611.14KB]Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB62261FTG, a PHASE-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and full-, half-, and quarter-step operation for less motor noise and smoother control. It has a wide operating voltage range of 10V to 38V with an output current capacity of 1.2A in addition to several built-in error detection circuits.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.11
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 128 times
Not followed.
License: MIT license
Download [613.77KB]Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB62262FTG, CLOCK-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and allows full-, half-, and quarter-step operation for less motor noise and smoother control. It has a wide operating voltage range of 10V to 38V with an output current capacity of 1.2A in addition to several built-in error detection circuits.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 168 times
Not followed.
License: MIT license
Download [614.41KB]Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB62269FTG, PWM method CLOCK-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and allows from full-step up to 1/32 steps resolution for less motor noise and smoother control. It has a wide operating voltage range of 10V to 38V with an output current capacity of 1.2A in addition to several built-in error detection circuits.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 159 times
Not followed.
License: MIT license
Download [611.79KB]Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S101AFG, a PHASE-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and full-, half-, and quarter-step operation for less motor noise and smoother control. It has a wide operating voltage range of 10V to 47V with an output current capacity of 2.8A in addition to several built-in error detection circuits.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 159 times
Not followed.
License: MIT license
Download [607.67KB]Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S102AFNG, CLOCK-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and allows full-, half-, and quarter-step operation for less motor noise and smoother control. It has a wide operating voltage range of 10V to 47V with an output current capacity of 2.8A in addition to several built-in error detection circuits.
[learn more] Author: MIKROE
Last Updated: 2024-10-31
Package Version: 2.1.0.10
mikroSDK Library: 2.0.0.0
Category: Stepper
Downloaded: 173 times
Not followed.
License: MIT license
Download [613.79KB]Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S109AFTG, CLOCK-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and allows from full-step up to 1/32 steps resolution for less motor noise and smoother control. It has a wide operating voltage range of 10V to 47V with an output current capacity of 2.8A in addition to several built-in error detection circuits.
[learn more] 
